Operating Elements
7
8
9
10
1
2
3
4
5
6
1 Lens lock
2 Main lens
3 Small magnifying lens
4 LED ring light
5 Flexible adjustment
6 Mode button
7 Base plate (removable)
8 Mounting clip
9 Power indicator LED
10 Micro-USB port
Installation
• Using the mounting clip
(8)
, clamp the device onto the supplied base plate
(7)
or a suitable horizontal surface (e.g. table,
work bench).
The rubber pads located on the base and attached to the end of the clip may leave marks on sensitive surfaces.
Do not use force to open the clip as this may damage the mount. Always make sure the lamp is securely clipped
before letting go. The maximum clamping range is 60 mm
Operation
• Connect the supplied USB cable to the Micro-USB port
(10)
and the other end to a power adaptor or USB port on your
computer.
• When connected to a power source, the power indicator LED
(9)
will illuminate.
• Touch the mode button
(5)
to turn the LED ring light
(4)
on.
• Touch again to cycle through colour temperatures (cool, warm).
• The LED ring light
(4)
will turn off after cycling through all temperatures.
- When the ring light is off, press and hold the mode button to gradually illuminate the LED ring light.
- When the ring light is on, press and hold the mode button to dim the LED ring light.
• Adjust the small magnifying lens
(3)
as follows. Turn the lens lock
(1)
counterclockwise to release the main lens
(2)
. Then
rotate the main lens until the small magnifying lens
(3)
is at the desired location. Turn the lens lock clockwise to secure the
main lens again.
The magnifier/lamp can be adjusted as required. Do not use excessive force to over bend or twist the flexible
section. Please hold the mounting clip while adjusting to prevent the lamp from falling over.
Care and Cleaning
• Disconnect the product from the power supply before cleaning.
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical solutions since these can
penetrate the housing or impair functionality.
• The product does not require any maintenance, do not disassemble it.
•
Clean the product with a dry, fibre-free cloth.
• Use a lens cleaning cloth for cleaning the lens. Alternatively, use a dry, clean, soft and lint-free cloth or a dust brush. If
necessary, you can moisten the cloth with a small amount of lukewarm water.
• When cleaning the lens with a cleaning agent, make sure not to directly apply the cleaner on the lens. Always apply the
cleaning agent to the cloth first.
• When cleaning, do not apply too much force on the lens or housing in order to avoid scratching.
• The LEDs are built-in and cannot be replaced.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At the end of its
service life, dispose of the product in accordance with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Input voltage / current ......................................5 V/DC, max. 500 mA via USB
Power consumption .........................................2 W
Illuminant .........................................................18 pcs SMD-LED (warm), 18 pcs SMD-LED (cold)
Luminous flux
..................................................max. 73 lm (warm), max. 70 lm (cold)
Color temperature ............................................4000 K (warm), 6000 K (cold)
Main Lens Ø ....................................................100 mm
Accessory Lens Ø ...........................................25 mm
Magnification factor
.........................................1.75x, 4x
Lens material ...................................................Glass
Operating / storage conditions .........................-20 to +40 °C, <95 % RH
Power cord ......................................................1.42 m
Dimensions (W x H x D) ..................................130 x 500 x 110 mm
Weight .............................................................1160 g
Operating Instructions
2 in 1 LED Table and Clamp Magnifier Lamp
Item No. 1595614
Intended Use
This product is intended for magnifying the view of objects. Dual 18 SMD LED ring lamps (warm and cool light) are located
around the lens. It can be secured to a suitable surface (e.g. table, work bench) using the base plate or mounting clip and is
powered via USB connection.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be avoided under
all circumstances. For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can result in short
circuits, fires, or other hazards. Read the instructions carefully and store them in a safe place. Make this product available to
third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and product names are
trademarks of their respective owners. All rights reserved.
Delivery Content
• Lamp
• USB cable
• Base plate
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the exclamation mark in the triangle is used to indicate important information in these operating
instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety information. If you do
not follow the safety instructions and information on proper handling in this manual, we assume no
liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for
children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
•
Always cover the lens or keep away from sunlight when not in use. There is a risk of fire during direct sunlight
since the lens acts like a burning glass.
•
Do not touch the lens with your fingers (especially finger nails) or sharp/pointed objects.
• Never use the lens to stare directly into bright light sources. There is a risk of eye damage!
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
• Do not operate the device unsupervised.
• The power supply must be located near to the device and be easily accessible.
• Never pull the USB cable from the power supply by pulling at the cable. Always pull the USB cable from the
power supply using the intended grips.
• Unplug the USB plug from the power supply if you do not use the device for an extended period of time.
• For safety reasons, always unplug the device in case of a thunderstorm.
• Make sure that the USB cable is not pinched, bent, damaged by sharp edges or put under mechanical
stress. Avoid excessive thermal stress on the USB cable from extreme heat or cold. Do not modify the USB
cable otherwise the USB cable may be damaged. A damaged USB cable can cause a deadly electric shock.
• Do not touch the USB cable if it is damaged. First, power down the respective power supply (e.g. via the
respective circuit breaker) and then carefully pull the USB plug from the power outlet. Never use the product
if the USB cable is damaged.
• To prevent risks, damaged power cables may only be replaced by the manufacturer, a professional workshop
appointed by the manufacturer, or a similarly qualified person.
• Never connect or disconnect the USB plug when your hands are wet.
• Never use the product immediately after it has been brought from a cold room into a warm one. The
condensation generated could destroy the product. Allow the device to reach room temperature before
connecting and using it. This may take several hours.
• Never pour liquids above or near the product.
•
Attach the clamp bracket to a horizontal, flat, and stable surface only. Do not attach any objects (e.g.
decorative material) to the product.
•
Never mount the product in the vicinity of easily flammable materials (i.e. curtains, fabrics, etc.). Make sure
no object (e.g. curtain) can touch or come near the lamp head, for example due to a draught. Otherwise
there is a risk of fire!
• For installations in industrial facilities, follow the accident prevention regulations for electrical systems and
equipment of the government safety organization or the corresponding authority for your country.
• Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our technical support
service or other technical personnel.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
*1595614_v5_1018_dh_02_m_4L
