e) Work Safety
•
Ensure that there is sufficient lighting.
•
Ensure proper ventilation during soldering.
Vapours can be harmful to your health.
•
Wash your hands thoroughly after working with
solder. This is particularly important when using
lead-based solder.
•
Do not put soldering alloys into your mouth. Do
not eat or drink during soldering.
•
Wear suitable protective clothing and safety
goggles when soldering. Liquid/splashing solder
may cause serious burns or eye damage.
•
For installations in industrial facilities, follow the
accident prevention regulations for electrical
systems and equipment of the government
safety organization or the corresponding
authority for your country.
Operating Elements
1
2
3
4
5
6
1
Curved tip
2
Tip fastening screw
3 Barrel
4
Power switch:
ON (
I
) / OFF (
O
)
5
Handle
6
Power cable
Setup the Stand
•
Set the stand by gently bending the holders up 90º
as shown.
•
Do not over bend or adjust too many times as this
may break the metal.
Operation
1. Connect the power plug to a mains power socket.
2. Turn the power switch ON
(4)
.
-
It takes approximately 18 minutes for the tip to heat up completely.
-
Place the soldering iron its stand when taking breaks or not in use.
3. Turn the power switch OFF and disconnect from the power supply when finished using. Allow to
completely cool down before storing it away.
Replace / Rotate the Tip
1. Make sure the soldering iron is disconnected from the power supply and completely cool.
2. Use a crosshead screwdriver and loosen all the tip fastening screws
(2)
.
Loosen the screws just enough for the tip to freely rotate or be removed.
3. Rotate the curved tip to the desired position or replace it.
4. Fasten the tip by tightening all the screws.
The screws should be tight enough so that the tip does not move during normal use.
Maintenance and Care
•
Always keep the tip tinned before switching off or storing for any period of time.
•
Never clean the tip with coarse, abrasive materials like files.
•
If oxide forms on the tip, lightly rub with abrasive paper, wipe clean, then immediately reheat and re-tin
the tip to prevent oxidation of the wettable surface.
•
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines. You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical Data
Input voltage ......................................... 230 V/AC 50 Hz
Power ................................................... 100 W (±10 %)
Temp ..................................................... max. 420 ºC
Heating time. ........................................ approx. 18 minutes to reach 420 °C
Cable .................................................... H05RR-F, 3 x 0.75 mm²
Tip
......................................................... ø9.5 mm
Operating/storage conditions ................ 0 to +40 ºC, 20 - 90 % RH (non-condensing)
Power cable length ............................... approx. 1.4 m
Dimensions (W x H x D) ....................... 408 x 126 x 51 mm
Weight .................................................. 647 g
Visit the Conrad website and search item no.
2226764
for information about any optional
accessories, spares, or replacement parts.
Operating Instructions
High Performance Soldering
Iron 100 W
Item No. 2226764
Intended Use
The product is a soldering iron suitable for rough
and mechanical soldering applications such as sheet
metal and installation jobs. It has a curved tip and
connects directly to a mains power outlet.
It is intended for indoor use only. Contact with
moisture must be avoided under all circumstances.
For safety and approval purposes, you must not
rebuild and/or modify this product. If you use the
product for purposes other than those described
above, the product may be damaged. In addition,
improper use can result in short circuits, fires, electric
shocks or other hazards. Read the instructions
carefully and store them in a safe place. Make this
product available to third parties only together with
its operating instructions.
This product complies with the statutory national and
European requirements. All company names and
product names are trademarks of their respective
owners. All rights reserved.
Delivery Content
•
Soldering iron
•
Stand
•
Operating instructions
Up-to-Date Operating Instructions
Download the latest operating instructions at
www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Safety Instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do not
follow the safety instructions and
information on proper handling in
this manual, we assume no liability
for any resulting personal injury or
damage to property. Such cases will
invalidate the warranty/guarantee.
a) Special Safety
•
The appliance is not to be
used by persons (including
children) with reduced
physical, sensory or mental
capabilities, or lack of
experience and knowledge,
unless they have been given
supervision or instruction.
•
Children shall not play with
the appliance.
•
Cleaning
and
user
maintenance shall not be
made by children without
supervision.
•
WARNING - This tool must
be placed on its stand when
not in use.
b) General Information
•
The device is not a toy. Keep it out of the reach
of children and pets.
•
Do not leave packaging material lying around
carelessly. This may become dangerous playing
material for children.
•
Protect the appliance from extreme
temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, steam and
solvents.
•
Do not place the product under any mechanical
stress.
•
If it is no longer possible to operate the product
safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer
be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor
ambient conditions or
-
has been subjected to any serious transport-
related stresses.
•
Please handle the product carefully. Jolts,
impacts or a fall even from a low height can
damage the product.
•
Consult an expert when in doubt about the
operation, safety or connection of the appliance.
•
Maintenance, modifications and repairs must
only be completed by a technician or an
authorised repair centre.
•
If you have questions which remain unanswered
by these operating instructions, contact our
technical support service or other technical
personnel.
c) Electrical Connection
•
The mains outlet must be located near to the
device and be easily accessible.
•
Never pull the mains plug from the socket by
pulling at the cable. Always pull it from the mains
socket using the intended grips.
•
Unplug the mains plug from the mains socket if
you do not use the device for an extended period
of time.
•
For safety reasons, always unplug the device
during thunderstorms.
•
Make sure that the mains cable is not squeezed,
bent, damaged by sharp edges or put under
mechanical stress. Avoid excessive thermal
stress on the mains cable from extreme heat or
cold. Do not modify the mains cable. Otherwise
the mains cable may be damaged. A damaged
mains cable can cause a deadly electric shock.
•
Do not touch the mains cable if it is damaged.
First, power down the respective mains socket
(e.g. via the respective circuit breaker) and then
carefully pull the mains plug from the mains
socket. Never use the product if the mains cable
is damaged.
•
To prevent risks, damaged power cables
may only be replaced by the manufacturer,
a professional workshop appointed by the
manufacturer, or a similarly qualified person.
•
Never plug in or unplug the mains plug when
your hands are wet.
•
Always lay the cables so that nobody can trip
over or become entangled in them. This poses
a risk of injury.
d) Operation
• Never touch the barrel
(2)
or tip
(1)
of the
soldering iron during use. Risk of burns!
•
Never use the soldering iron to heat up liquids.
•
Never solder live electrical components or parts.
Always switch off the power before-hand.
•
Do not cover or fasten any items to the soldering
iron. Otherwise there is a risk of fire.
•
Touching or soldering capacitors (or similar
components) or leads/cables that are connected
to capacitors may cause a fatal electric shock!
Capacitors may stay charged for several hours
after you switch off the power supply!
•
Always solder on non-flammable surfaces.
Protect other materials nearby from damage
through heat.
•
Risk of fire or explosion! Do not use around or
near explosive or flammable materials.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
*2226764_v1_0620_02_dh_m_en
