TonerRefillKits ReChargX RX180 Скачать руководство пользователя страница 8

Страница: 8 / 10

TonerRefillKits.com

RechargX™ RX180 v2

Mon - Fri 8am - 5pm ET

2012.02.21

Page 8 of 10

Step 19: Apply the Leak-Proof Seal

Remove the protective backing from the

ReChargX™ leak-proof seal (figure 20) and

lower the seal around the waste hopper

hole.

Press firmly around the entire seal to ensure

the seal securely sticks to the toner cartridge,

as shown in figure 21.

Step 20: Locate the Toner Cartridge Reset

Chip

The last step of the ReChargX RX180 Premium

Print Toner Refill instructions is to replace the

toner cartridge reset chip.

Orient the toner cartridge so the handle of the

cartridge is facing away from your chest and the

reset chip is closest to you (figure 22).

The white box in figure 22 shows the location of

the toner cartridge reset chip.

Figure 20:

Removing the ReChargX™ leak-proof seal

from the protective backing

Figure 21

: Waste hopper with ReChargX™ seal in place





Figure 22

: The toner cartridge reset chip location

Содержание ReChargX RX180











Результаты поиска

Содержание ReChargX RX180

Отзывы:

Похожие инструкции для ReChargX RX180

Бренды по названию

Популярные бренды

TonerRefillKits ReChargX RX180, Инструкция по эксплуатации

Результаты поиска

Содержание ReChargX RX180

Отзывы:

Похожие инструкции для ReChargX RX180

Бренды по названию

Популярные бренды