background image

 

 

 

 

Symbol 

Please observe all safety precautions listed below. 

WARNING:

This may cause an accident resulting in injury or death if it is not observed. 

CAUTION:

This may cause injury, damage or trouble to the air tool or equipment if it is not followed. 

 

WARNING 

To reduce risk of injury, everyone using, installing. repairing, maintaining changing accessories on, or working 
near this tool MUST read and understand these instructions before performing any such task. 

DO  NOT  DISCARD  –  GIVE  TO  USER

 

   

 

 

Do not use a Rack Drill until this safety instruction has been read and understood completely.   
This manual is necessary to help you to use the Rock Drill correctly. 

 

 

WARNING 

 
Do not use a Rock Drill before reading this safety instruction manual.   
Obey all of the safety measures indicated in this manual   

 

FOR DETAILED INFORMATION ABOUT TOKU AIR TOOLS AND EQUIPMENT 
CONTACT TO

 

 
Air & Allied Sales (Pacific) Pty Ltd 
HEAD OFFICE
1/50 Success Street, Acacia Ridge, QLD 4110, AUSTRALIA

 

     

           

                                             

           

   

                      13th edition 

 

OPERATOR’S INSTRUCTIONS 
AND PARTS LIST 

 

AIR HAND HAMMER 

MODEL 

TJ-15

 

 

 

 

 

 

[email protected]

Air & Allied Sales (Pacific) Pty Ltd

www.air-allied.com.au

www.air-allied.com.au 

Содержание AIR & ALLIED SALES TJ-15













Отзывы: