background image

3

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe

operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or

cautions regarding safety.

• After reading, keep this manual handy for future reference.

Safety Symbol and Message Conventions 

Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards. 

Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury. 

WARNING

When Installing the Unit

• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface.

Doing so may result in the unit falling down and causing personal injury and/or property damage. 

• Refer all installation work to the dealer from whom the speaker was purchased. Installation requires

extensive technical knowledge and experience. The speaker may fall off if incorrectly installed, resulting in
possible personal injury.

• Flying Precautions 

Be sure to follow the instructions below. Otherwise, the suspension wires or belts may be off or snap and
the speaker may fall off, causing personal injury.

· Check to confirm that the suspension wires and belts are strong enough to withstand the speaker load.
· The connectors of the suspension wires and belts must be securely linked with those of the speaker.
· All parts and components (such as enclosures, metal pieces, and screws) must be free from any

deformation, crack, and corrosion. 

· Be sure to use screws supplied with the optional flying hardware when installing the speaker using such

hardware. 

• Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket.

Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.

• When installing the unit in the snowy area, take appropriate measures to prevent snow from lying on the

unit. If the snow lies on the unit, the unit may fall, causing personal injuries. 

• Owing to the unit's size and weight, be sure that at least two persons are available to install the unit. Failure

to do so could result in personal injury.

• Do not use other methods than specified to install the speaker. Extreme force is applied to the unit and the

unit could fall off, possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so

may cause the speaker to fall, resulting in material damage and possible personal injury. 

• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent

accidents that could result in personal injury.

• Use the specified mounting bracket in combination. Doing otherwise may cause the unit or component to fall

off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration. The mounting bracket can be damaged by

excessive vibration, potentially causing the unit to fall, which could result in personal injury.

Содержание SR-S4LWP

















Отзывы: