Toa MX-401 Скачать руководство пользователя страница 3

The  TOA  MX-401  is  a  very  compact,  four  channel  self-powered  mixer.  It  was
designed  to  deliver  maximum  features  and  performance  in  a  cost-effective  portable
PA  package.

The  MX-401  features  four  input  channels,  one  program  output,  and  one  Foldback
output.  The  internal  amplifier is  rated at  100 watts into  an 8 ohm load,  and  150 watts
into  4  ohms.
Each  input  channel  has  an  electronically  balanced  XLR  connector,  and  a  high-
impedance  unbalanced 1/4" phone  jack.  In  addition, each  channel  features  two-band

EQ,  a  pre-EQ  Foldback  send,  and  post-EQ  reverb  send.
The master control section features  a patchable  5-band graphic  equalizer,  a q u a l i t y 3-
spring  reverb,  a  full  patch  bay  with  1/4"  phone  auxiliary  and  RCA  tape  inputs,  and
master volume controls for Program, Foldback, and Reverb return to both. The power
amp  protection circuitry  and  autocomp  compressor,  both  with  LED's,  are also located

in  this  section.

1.  Four  input  channels

2.  100  watts  into  8  ohms,  150  watts  into  4  ohms

3.  Patchable  5-band  graphic  EQ

4.  Auto  Comp  compression  unit  w/LED

5.  Built-in  spring  reverb

6.  Power  amp  protection  circuitry  w/LED

7.  Full  patch  bay

8.  Aux  input  w/level  control,  RCA  jacks  and  parallel  phone  1/4"  jacks.

9.  Reverb  level  to  PGM  and  FB

10.  Independent  Foldback  mix.

Each  Channel

1.  Input  level  control

2.  Two  band  EQ

3.  Pre-EQ  Foldback  send

5.  Low-Z  electronically  balanced  XLR  input

6.  Hi-Z  unbalanced  1/4"  input

—   2

 —

General  Description

Features

All manuals and user guides at all-guides.com

Содержание MX-401












Отзывы: