Toa HX-7B Скачать руководство пользователя страница 14

14

10. SAFETy WIRE INSTALLATION

Be sure to always use safety wire when installing speaker 

systems.

Note

Safety wires, shackles, and other suspension parts are not 

supplied with the speaker systems, and must be prepared 

separately. 

[Wall Mounting Example]

In this example, the optional HY-VM7B and 

HY-WM7B brackets are used. 

Weight: 39.8 kg (87.74 lb)

Wall

Make as short as 

possible so as not 

to slacken.

Rear angle bar

 Shackle

Safety wire

Be sure to follow all instructions regarding safety wire 

installation. If not correctly followed, speakers could fall, 

potentially resulting in personal injury. 

•  Use safety wire that is strong enough to suspend the 

full weight of the components to be installed.

•  Attach  a  shackle  to  the  rear  angle  bar  and  install 

suspension bolts to the wall or ceiling as shown in the 

figure at right.

•  Only install speaker systems in locations capable of 

structurally supporting the weight of the speakers and 

their mounting brackets. 

WARNING

Note

Attach at least 2 safety wires to the shackle, 

then secure them to the wall as shown above.

Содержание HX-7B





















Отзывы: