7. CONNECTION
8. OPERATION
9. USING THE SWITCH SELECTOR MODE
Step 1. Set the amplifier's microphone volume control to the minimum position.
Step 2. Using the supplied cable or STP cable of straight type to connect with other equipment ( amplifier, mixer, PA
system, etc )
After announcement is completed, press the microphone ON/OFF button. Both of the unit’s lamp will light blinks
blue and microphone turn off.
Selector switch have 2 modes. There are battery mode and DC power mode. If using battery as power input, select the
switch to battery position and if using DC input as power input, select to DC power position.
Note : For using RJ45 as mic out and power input, set the switch to DC input position, but if just as mic out, can use one
of the switch selector mode.
URL: http://www.toa.com.sg
133040001800
Traceability Information for Europe
Manufacturer : Authorized representative :
PT. TOA GALVA INDUSTRIES
TOA Electronic Europe GmbH
Jl. Raya Bogor km 34-35, Tapos
Suederstrasse 282, 20537 Hamburg,
Depok 16958, Indonesia
Germany
Caution : To release the batteries, please pull the remaining ribbon carefully from the battery compartment.
6.2. Battery Insertion
Step 3. Put back the battery cover to product.
8. XLR Balance Output
10. Battery Compartment
Output impedance of the microphone is 600 ohms. Use the
supplied cable to connect with an amplifier.
Place AA batteries ( 4 pieces ) .
9. RJ45 Balance Output
Use STP cable of straight type to connect with other equipment.
Pin configuration : Pin 1, 2: contact output;
Pin 3: NC
(Not Connected); Pin 4: Audio Output (H);
Pin 5: Audio Output (C); Pin 6: NC; Pin 7: 24
VDC; Pin 8: Ground /E.
6. BATTERY
6.1. Life Span
Application and use battery for paging be assumed 150 times/day and unit can use
until 20 months or 90 thousand calls.
-
+
-
-
+
-
+
+
1
2
3
3
Step 1. Open the battery cover. Insert the battery according to battery polarity and ribbon
position (see the right picture)
Step 1. Press the microphone ON/OFF button. The mic lamp and the power lamp light blinks blue and turning on the
microphone.
Step 2. Keep your mouth 5 – 10 cm away from the microphone and speak normally for the best possible sound repro-
duction. Adjust the microphone orientation for the best position by turning its mic shaft. If distance of mouth is
too near, it cause voice distortion. Adjust the microphone by pulling away or lowering it. Because the high sensi-
tivity’s microphone.
Step 3.
Note : Be sure to press the ON/OFF button after announcement completion. Failure to do this, shortening the battery
life. Be sure to turn off the phantom power on other equipment if use chime microphone for durability of unit.
10. SPECIFICATION
Element
Condensor Microphone
Polar Pattern
Cardioid
Impedance
600
ohm, Balanced
Sensitivity
Microphone : -41 ± 3dB (1kHz 0dB = 1V / Pa)
Chime Tones : -31 ± 3dB ( posisi maksimum )
Power Source
6V DC (4 x "AA" battery ) or DC power ( 9 - 24 V)
Frequency Response
Finish
Stand = ABS Resin, Hitam, Cat
Weight
558 g ( exclude batteries)
Acessories
50 - 18,000 Hz
Operating Temperature
0 °C to +40 °C (32 °F to 104 °F)
Shaft = Copper alloy, HItam, Cat
Windscreen ..... 1
XLR to Phone Jack Cable (7.5m) ....1
Dimensions
110 (w) x 145 (d) x 532 (h) mm
Current Consumption
13 mA when chime and 6 mA microphone operate
Chime Tones
4 - Tones chime ( UP / DOWN )
Connector Output
XLR 3 - 32 Equivalent
RJ45 : Audio output, power supplyi dan control output
Note : The design and specifications are subject to change without notice for improvement.
