TLV JL14-X Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 19

background image

172-65441A-04 (JL14-X/JLH14-X/JLH14-B) 20 Jan 2021

10

Disassembly/Reassembly

NEVER apply direct heat to the float. The float may explode due to

increased internal pressure, causing accidents leading to serious injury

or damage to property and equipment.

WARNING

Use hoisting equipment for heavy objects (weighing approximately

20 kg (44 lb) or more). Failure to do so may result in back strain or other

injury if the object should fall.

CAUTION

When disassembling or removing the product, wait until the internal

pressure equals atmospheric pressure and the surface of the product

has cooled to room temperature. Disassembling or removing the

product when it is hot or under pressure may lead to discharge of fluids,

causing burns, other injuries or damage.

CAUTION

Use the following procedures to remove components. Use the same procedures in
reverse to reassemble. (Installation, inspection, maintenance, repairs, disassembly,
adjustment and valve opening/closing should be carried out only by trained
maintenance personnel.)

In cases where sufficient space has been secured for maintenance (see the
maintenance space diagram in the

“Installation” section), it is possible to perform

maintenance without disconnecting the inlet and outlet piping. If there is insufficient
maintenance space, first disconnect the inlet and outlet piping, then move the unit to
a spacious area in which to carry out maintenance.

Removing/Reattaching the Drain Plug

Remove any condensate from inside the body before beginning disassembly.

Part

During Disassembly

During Reassembly

Drain Plug -Remove with a wrench -JL14-X: Wrap 3

– 3.5 turns of sealing tape around the

threads; consult the table of tightening
torques and tighten to the proper torque

-JLH14-X/JLH14-B (Option): Consult the table of

tightening torques and tighten to the proper
torque

Drain Plug
Gasket
(JLH14-X /
JLH14-B
(Option))

-Remove the gasket and

clean sealing surfaces

-Replace with a new gasket; coat surfaces with anti-

seize

Drain Plug

Drain Plug

Gasket

Drain Plug

JL14-X

JLH14-X /

JLH14-B (option)

Drain Plug

«
...
9
10
11
12
13
...
»

Содержание JL14-X




















Отзывы:

Нет отзывов

Похожие инструкции для JL14-X

Бренд: Rath Страницы: 3

Бренд: Federal Страницы: 43

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: Raymarine Страницы: 124

Бренд: Raymarine Страницы: 192

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

LSP400 LED Series

Бренд: WE-EF Страницы: 6

Бренд: hager Страницы: 4

Бренд: ubicquia Страницы: 36

Бренд: Fagor Страницы: 92

Бренд: Masterclock Страницы: 19

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренд: Cuisinart Страницы: 159

DJ Laptop stand +tray

Бренд: Power Dynamics Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды