background image

 

WARRANTY  and  SAFETY 

 

Warranty:

   The scissor lift model identified in this manual has the following warranty  

                       from date of purchase: 

 

Structural Components

 

- 5 years                                    Accessory Items - 90 days 

Hydraulic and Other Components  - 1 year                    Labor - 1 year          

 

The above items are warranted to be free of defects in material and workmanship to the 

original owner of the lift as follows:  During the first year 

(90 days for accessories)

, those parts 

proven after inspection to be defective shall be repaired or replaced at the option of the 
manufacturer.  Structural components only are warranted for an extended four years and if 

proven after inspection to be defective shall be repaired or replaced at the option of the 
manufacturer.  This warranty does not extend to defects caused by ordinary wear, misuse, 
abuse, improper maintenance, shipping damage or where repairs have been attempted or 
made by anyone other than the manufacturer or a manufacturer certified technician.  This 

warranty is exclusive and in lieu of all other warranties express or implied.  In no event shall 
the manufacturer be liable for special, incidental or consequential damages for any breach or 
delay in performance of the warranty.  The manufacturer reserves the right to change 

specifications, designs or add improvements to its product line without incurring any obligation 
to make such changes to products sold previously. 

 

IMPORTANT SAFETY INSTRUCTIONS 

 

When using your garage equipment, basic safety precautions should always be followed, 

including the following: 

 

1.

 

Read all instructions 

2.

 

Care must be taken as burns can result from touching hot parts 

3.

 

Do not operate equipment with a damaged cord or if equipment has been dropped or 
damaged – until it has been examined by a qualified service person 

4.

 

Do not let a cord hang over the edge of the table, bench, or counter or come in contact 
with hot manifolds or moving fan blades 

5.

 

Let equipment cool completely before putting away.  Loop cord loosely around 

equipment when storing 

6.

 

To reduce risk of fire, do not operate equipment in the vicinity of open containers of 
flammable liquids (gasoline) 

7.

 

Adequate ventilation should be provided when working on operating internal 
combustion engines 

8.

 

Keep hair, loose clothing, fingers, and all parts of body away from moving parts 

9.

 

To reduce the risk of electric shock, do not use on wet surfaces or expose to rain 

10.

 

 Use only as directed in this manual.  Use only manufacturer’s recommended 
 attachments 

11.

 

 ALWAYS WEAR SAFETY GLASSES.  Everyday eyeglasses only have impact resistant 

 lenses, they are not safety glasses 

 

SAVE THESE INSTRUCTIONS 

                                                                           

                                                                                                                    safety cont’d on page 5 

Содержание TLSS10ALORR1































Отзывы: