TJERNLUND VP-2F Скачать руководство пользователя страница 14

MAINTENANCE

1. The VP-2F & VP-3F motors are permanently lubricated and do not need to be oiled.

2. The owner must semiannually inspect the vent hood and vent pipe for blockage, corrosion and leaks.

3. A vent system inspection must be performed annually by a qualified service agency. The inspection should include the 

operation circuit check, safety interlock test, combustion air test and a visual inspection of the complete vent system for 
corrosion, blockage and leaks. Any corrosion, blockage or leaks detected, must be replaced or repaired immediately.

HOW TO OBTAIN SERVICE ASSISTANCE

1.

If you have any questions about your Power Venter or if it requires adjustment, repair or routine maintenance, we suggest that
you contact your installer, plumbing contractor or service agency.

2.

If you require technical information contact Tjernlund Products, Inc. at 1-800-255-4208.

When contacting Tjernlund Products, Inc., please have the following information available:

1.

Model number of the Power Venter 

2.

Name and address of installer and service agency

3.

Date of original installation and dates any service work was performed

4.

Details of the problem

LIMITED PARTS WARRANTY AND CLAIM PROCEDURE

Tjernlund Products, Inc. warrants the components of its products for one year from date of installation.  This warranty covers defects
in material and workmanship.  This warranty does not cover normal maintenance, transportation or installation charges for replace-
ment parts or any other service calls or repairs.  Products that are tampered with, damaged, installed improperly, wired incorrectly or
defective due to malfunctioning appliances are not covered under this warranty.  This warranty DOES NOT cover the complete Power
Venter if it is operable, except for the defective part.

1.) Follow troubleshooting guide to determine defective component.  If unable to determine faulty component, contact your Tjernlund 

distributor or Tjernlund Products Technical Customer Service Department at 1-800-255-4208 for troubleshooting assistance.

2.) After the faulty component is determined, return it to your Tjernlund distributor for replacement.  Please include Venter date code 

component was taken from.  The date code is located on the Electrical Box coverplate.  If the date code is older than 1 year, you 
will need to provide a copy of the original installation receipt to your distributor.  Credit or replacement will only be issued to a 
Tjernlund distributor after the defective part has been returned prepaid to Tjernlund and verified defective.

13

REPLACEMENT PARTS LIST

ITEM

PART NUMBER

VP-2F Vent Hood 

VH1-3

VP-3F Vent Hood

VH1-4 

VP-2F Venter Motor

950-2020

VP-3F Venter Motor

950-1020

Gas Pressure Switch

950-2080

24V Transformer

950-2030

Post Purge Relay/Timer

(approx. 45 second non-adjustable delay) 950-0014

Post Purge Relay/Timer

(1 to 10 minute adjustable delay)

950-1067

Linear Limit Spill Switch

950-2064

TJERNLUND LIMITED ONE YEAR WARRANTY

Tjernlund Products, Inc. warrants to the original purchaser of this product that the
product will be free from defects due to faulty material or workmanship for a period
of (1) year from the date of original purchase or delivery to the original purchaser,
whichever is earlier.  Remedies under this warranty are limited to repairing or replac-
ing, at our option, any product which shall, within the above stated warranty period,
be returned to Tjernlund Products, Inc. at the address listed below, postage prepaid.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF, AND TJERNLUND PRODUCTS, INC. EXPRESSLY DIS-
CLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
FROM THE USE OF THIS PRODUCT.  THIS WARRANTY IS IN LIEU OF ALL
OTHER EXPRESS WARRANTIES AND NO AGENT IS AUTHORIZED TO ASSUME
FOR US ANY LIABILITY ADDITIONAL TO THOSE SET FORTH IN THIS LIMITED
WARRANTY.  IMPLIED WARRANTIES ARE LIMITED TO THE STATED DURATION
OF THIS LIMITED WARRANTY.  Some states do not allow limitation on how long an
implied warranty lasts, so that limitation may not apply to you.  In addition, some
states do not allow the exclusion or limitation of incidental or consequential damages,
so that above limitation or exclusion may not apply to you.  This warranty gives you
specific legal rights and you may also have other rights which may vary from State to
State.  Send all inquiries regarding warranty work to Tjernlund Products, Inc. 1601
9th Street, White Bear Lake, MN 55110-6794.  Phone (651) 426-2993 • 
(800) 255-4208 • Fax (651) 426-9547  • Email: [email protected]

Содержание VP-2F
















Отзывы: