Titgemeyer MS 75 Скачать руководство пользователя | Manualshive

Страница: 7 / 37

background image

7

Safety instructions

The riveting tool is solely designed for setting locking ring bolts and blind
rivets. The riveting tool MS 75 is designed for the processing of locking
ring bolts with a nominal shaft diameter of 5.0 to 6.5 mm made of alumini-
um, steel and stainless steel and for blind rivets with a rivet shaft diameter
of 5.0 to 6.5 mm made of aluminium, steel and stainless steel.
This riveting tool must be used only as a hand-held device!
The client is fully responsible for any modifications to the riveting tool!

Never throw away or drop the riveting tool!

Please take care that only clean and dry compressed air is let into the
riveting tool. Moisture and dirt can damage the riveting tool. Use only such
compressed air, which falls into class 2 of air quality as per ISO 8573-1.

Caution

Hazard of injury because of explosion! Never use the riveting
tool in an atmosphere prone to explosions. Ensure that the
workplace is well lit and clean.
Hazard of injury due to the openly moving compressed air
hose. Connect and lay the compressed air hose properly.
Hazard of injury due to tripping over! Lay the compressed air
hose in such a way that nobody should trip over it.

Attention

Material damage! The maximum operating pressure is 7 bar.
For increasing the durability of the riveting tool, it is recommen-
ded to fit a compressed air-maintenance unit in the compressed
air hose.

Application as per the purpose

Improper use

Clean and dry compressed air

H

E

«
...
5
6
7
8
9
...
»

Содержание MS 75






































Отзывы:

Нет отзывов

Похожие инструкции для MS 75

Бренд: Gage Bilt Страницы: 12

Бренд: Gage Bilt Страницы: 13

Бренд: Gage Bilt Страницы: 9

Бренд: Gage Bilt Страницы: 10

Бренд: Q-tran Страницы: 5

Бренд: WAGNER Страницы: 12

Бренд: Wayne Страницы: 8

Бренд: Rockwell Automation Страницы: 4

Бренд: Milwaukee Страницы: 4

Бренд: Metabo Страницы: 72

Бренд: Wolf Garten Страницы: 198

Бренд: Samoa Страницы: 8

Бренд: Scheppach Страницы: 48

ShopMaster CL180JS

Бренд: Delta Страницы: 15

Бренд: HARTING Страницы: 2

Бренд: Kärcher Страницы: 68

Бренд: Far Tools Страницы: 52

Бренд: LEVIOR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды