background image

4

AVOID ELECTRICAL SHOCK

PREVENT FIRES

DON'T OVERREACH

PROTECT YOUR HANDS

DON'T FORCE TOOL   

DISCONNECT POWER

AVOID INJURY FROM UNEXPECTED ACCIDENT

INSPECT YOUR LOG

KEEP BYSTANDERS AWAY

Check that the electric circuit is 
adequately protected and that it 
corresponds with the power, voltage 
and frequency of the motor. Check 
that there is a ground connection. 
Ground the log splitter. Prevent body 
contact with grounded surfaces: pipes, 
radiators, ranges, and refrigerator 
enclosures. Never open the switch / 
plug box. Should this be necessary, 
contact a qualified electrician. Make 
sure your fingers do not touch the 
plug's metal prongs when plugging or 
unplugging the log splitter.

Do  not  smoke  or  have  open  flames 

when  operating  or  refilling  the  log 

splitter. Never operate the log splitter 

near a flame or spark. Oil is flammable 

and can cause explosions.

Keep  proper  footing  and  balance  at 

all  times.  Never  stand  on  log  splitter. 

Serious  injury  could  occur  if  the  tool 

is  tipped  or  if  contact  is  made 

with  the  cutting  tools.  Do  not  store 

anything  above  or  near  the  log 

splitter,  to  avoid  encouraging  anyone 

to  stand  on  the  tool to reach them.

Keep your hands away from splits and 
cracks which open in the log. They may 
close suddenly and crush your hands. 
Do  not  remove  jammed  logs  with 
your hands. 

It  will  do  a  better  and  safer  job  at 

its  design  rate.  Don't  use  this  log 

splitter  for  any  purpose  for  which 

it  was  not  intended.  Do  not  alter 

the  equipment,  or  use  the  equipment 

in  such  a  way  as  to  circumvent  its 

design  capabilities  and  capacities. 

Never  try  to  split  logs  larger  than 

those

 

indicated

 

in

 

the specifications 

table.

Unplug when not in use, before making 

adjustments, changing parts, cleaning, 

or working on the log splitter. Consult 

the technical manual before servicing.

Do  not  straddle  or  reach  across  the 

splitting  area when  operating  the log 

splitter.  Never  pile  logs  to  be  split  in 

a manner that will cause you to reach 

across  the  log  splitter.  Only  use 

your  hands  to  operate  the  control 

levers.  Never  use  your  foot,  knee,  a 

rope,  or  any  other  extension 

device.  Always  pay  full  attention  to 

the  movement  of  the  wedge  ram. 

Never  attempt  to  load  your  log 

splitter  while  the  ram  is  in  motion. 

Keep  hands  out  of  the  way  of  all 

moving parts. Never try to split two 

logs  on  top  of  each  other,  as  this 

may cause one to fly up and hit you.

Never attempt to split logs containing 

nails,  wire  or  other  debris. 

Always  make  sure  that  both  ends 

of  the  log you  are  splitting  are  cut 

as  square  as possible.  This  will 

prevent  the  log  from  sliding  out 

of  position  while  under  pressure. 

Branches  must  be cut off, flush with 

the trunk.

Allow  only  one  person  to  load  and 

operate  the  log  splitter.  Always  keep 

bystanders,  including  visitors,  children 

and  pets  away  from  the  work  area, 

especially  when  the  log  splitter  is  in 

operation.  Only  the  operator  should 

stand near the machine and only within 

the 

safe 

operating 

area 

as 

described  in  this  manual.  Never 

use  another  person  to  help  you 

with  freeing  jammed  logs.  No  one 

under  the  age of 16 should be allowed 

to  operate  the  log  splitter.  Any 

individual  under  the  age  of  18  should 

have  the  necessary  training  and 

skills  to  perform  the  functions 

properly  and  safely,  and  should 

always be under adult supervision.

Содержание TPLS11TV


















Отзывы: