1
INSTRUCTIONS
WARNING: READ ENTIRE MANUAL AND COMPLY WITH ALL SAFETY AND SERVICE
PRECAUTIONS. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR IF
INSTRUCTIONS ARE NOT FOLLOWED CAREFULLY.
UNPACKING AND SET-UP *REFER TO PARTS LIST FIG. 1
1. Carefully unpack the lift making sure that all of the parts have been included.
2.
Remove the lift and all parts from delivery pallet and place on a clean, solid flat surface.
3. Take end of black Hydraulic Hose and attach to the Power Unit Assembly (67).
4.
Remove the fill cap from the power unit and fill the oil tank reservoir between the minimum and
maximum range on the fill cap dipstick. To fill the oil tank reservoir, the lift must be completely
lowered. Fill the oil tank with a permium quality IS0-32 or AW-46 Hydraulic oil.
5. Plug the hydraulic power unit into a standard 110V - 120V 60Hz AC outlet. Unit must be
plugged into a dedicated circuit on a 15 amp circuit breaker. Raise the lift by pressing the green
button on the control panel to expose the top of Casters (22). Note: If the lift is not raising
level, check to make sure that the Wheels (42) are in their tracks.
6. Use the provided Allen wrench and place in top of Casters (22) and turn it clock-wise. Lower all
four casters until the lift rolls freely.
7. If using the Front Extension (9), slide the Front Extension over the front of the Deck Plate. Use
the second and third Connecting Bars (5) and secure to the Deck Plate with the Quick Pins (3)
or use Short Connecting Bar (68) without Side Extensions.
8. If using Side Extensions (7) then use the Connecting Bar (5) to assemble the Side Extensions
(7) to the Deck Plate (8) securing them with the Quick Pins (3). Slide the Side Extensions (7) to
the Deck Plate (8).
9. Take Ramp Stands (43) and screw into Bottom Ramps (44) and (46). Place the Extension
Ramp (47) over matching holes on the Center Ramp (45).
10. Take the Fixed Clamp (10) and bolt to location “B” on the Deck Plate (8) or Front Extension (9)
Using Bolts (11), Washers (12), Lock Washers (13), and Nuts (14) (Optional Equipment).
11. Take the Crank Assembly (69) and bolt to location “C” on the Deck Plate (8) or Front Extension
(9) using Bolts (11), Washers (12), Lock Washers (13) and Nuts (14). Bolt Moveable Clamp (16)
to Crank Assembly (69) using the provided Bolts (70) (Optional Equipment).
12. Insert the Tire Stop (15) onto the Fixed Clamp (10) using the Pin (60)(Optional Equipment).
13. Place Stands (1) on holes located on the end of the Deck Plate (8).
14. If necessary, raise or lower the Adjustment Legs (6) to make the lift Deck Plate (8) level with
the Ramps.
NOTE:
The Stands (1) are for holding up a motorcycle with rear wheel removed. (Straps not
provided but should be used).
NOTE:
Standard Dropout Plate (2) can be removed for easy rear wheel removal.
NOTE:
Roller Dropout Plate (4) can be installed after motorcycle is loaded for easy rear
wheel cleaning or maintenance.
WARNING:
Roller Dropout Plate (4) must be removed prior to unloading the
motorcycle from the lift & replaced with the Standard Dropout (2). Do NOT operate
motorcycle on Roller Dropout (4). Roller Dropout (4) is
NOT
to be used as a dyno device.
Содержание HDML-1500XLT-E
Страница 7: ...4 PARTS LIST FIG 1 PLEASE MAKE SURE TO CONFIRM THAT ALL PARTS ARE INCLUDED...
Страница 14: ......
