adjustment of the “Off time” ranges from three (3) minutes to eight (8) hours.
The switch is used to determine when the controller will be active. The switch in the up
position, configures the timer to be active during the “DAY” only. If the switch is placed in the
down position, the timer will be active during the “NIGHT” only. The controller can also be
configured to operate during “BOTH” the day and the night by placing the switch in the center
position. The controller will cycle the load output on and off in accordance with the preferred
settings. When the output is on, the “ACTIVE” LED will illuminate. The Apollo 1 provides up to
15 amps of capacity on a standard 120 volt circuit. The Apollo 1 is built with the highest quality
components and will provide the user with years of trouble free service.
Instructions for Operation
• Securely mount your Apollo 1 in your enclosure and away from any spray, water or mist.
• Set the “On time” to activate your equipment at preferred setting.
• Set the “Off time” to deactivate your equipment at preferred setting.
• Plug your equipment into the female side of the piggyback cord set.
• Turn on your equipment to desired setting.
• Plug the male side of the piggyback cord set into a 120 volt/15 amp maximum branch circuit
outlet. Use of a surge protection power strip is recommended.
• Turn the power switch of the controller to the “ON” position.
• Your Apollo 1 will now control your equipment at the desired settings until the power is defeated.
• To reset your Apollo
1. Simply turn “OFF” the switch, adjust your settings, and turn “ON“ the power
switch to activate controller at new settings.
Troubleshooting Tips
If the Apollo 1 is not performing as expected, try the following:
a. Confirm that your power input is active and providing
120 volts/15 amps to the controller.
b. Check the voltage output of your piggyback cord set using a voltage test meter,
fan or 120 volt light to verify power is flowing through controller.
c. Make sure that your “DAY/BOTH/NIGHT” switch is in the correct
mode for your application.
d. If your Apollo 1 is not functioning in the correct mode, check the photocell to see if
there is anything covering the photocell. If so, clean the lens using warm water on
a soft cloth.
e. If timing is incorrect , try turning “On time” / “Off time” knobs slightly higher or lower
to achieve correct timing pattern. Once correct settings have been achieved,
Apollo 1 will cycle at those settings until power is interrupted.
f. If you are still having problems with your Apollo 1, please contact our Technical
Service Representative to assist you further.
Warranty Information
• Titan Controls warrants the original purchase of this product against defects in material and
workmanship under normal use for three (3) years from the date of purchase.
• During the warranty period, Titan Controls will, at our option, and without charge, repair or
replace this product if the controller or any of its components fail or malfunction.
• All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA)
number prior to any service of the product.
• This warranty is expressly in lieu of all other warranties, expressed or implied, including the
warranties of merchantability and fitness for use and of all other obligations or liabilities on the
part of the seller.
• This warranty shall not apply to this product or any part thereof which had been damaged by
accident, abuse, misuse, modification, negligence, alteration or misapplication.
• Controllers with serial numbers or date tags that have been removed, altered or obliterated;
broken seals or that show evidence of tampering; mismatched board serial numbers or
nonconforming parts, are excluded from coverage.
• Titan Controls makes no warranty whatsoever in respect to accessories or parts not
supplied by Titan Controls.
• Monetary refunds of the warranty will not be given.
• The Buyer assumes all responsibility regarding the use & installation of this controller.
• All warranty service is provided through the factory or an authorized service representative.
• This warranty shall apply only to the United Sates, including Alaska, Hawaii and territories of the
United States.
• Defective controllers need to be returned with the “proof of purchase/receipt”.
• For additional warranty information, contact a Titan Controls Technical Service
Representative or your Dealer.
• NOTE: Titan Controls is a manufacturer of environmental controls. All sales offerings to the
public are done through a nationwide group of Dealers. No sales offerings will be made
directly to the general public.
Service and Repair Program
• For all service and repairs please contact one of our Technical Service Representatives for a
Return Merchandise Authorization (RMA) number.
• All factory service & repairs will be completed within 48 hours of receipt of controller and after
authorization by customer for repairs.
• Titan Controls will, at its discretion, repair or replace the controller.
• Factory calibration services are available for all Titan Controls. Returning Units: Please contact
your retail store for returns.