19
E
N
G
L
I
S
H
18
E
N
G
L
I
S
H
Reassembling Receiver Halves:
STEP 1:
❏
Double check that the Trigger Assembly
; and other parts: Feed Elbow Lock
+ Pin
+ Spring
; Front
Bolt*
; Ball Latch
; Linkage Arm*
; Link Arm Pins (2)
; Rear
Bolt*
+ Bolt Insert
; Bolt Handle
; Drive Spring*
+ Guide
Pin*
; Buffer O-ring
; End Cap
+ End Cap Cover
; 2 Tank
Adapter Nuts
; are in place and (*=oiled) (see below and schematics
on pages 11–12 for details as needed).
❏
❏
❏
❏
❏
Non-E-Trigger
TM
Markers go to STEP 2) on page 19.
For E-Trigger
TM
Markers:
Do not operate sear tripper assembly uninstalled as solenoid / armature
may pinch you.
E-Trigger
TM
Parts Not Shown
in Basic Parts List on
(pages 12-13)
TA06020 Armature Pin
TA09935
Electronics
Assembly
TA05014 Magnet
Solenoid
-Armature
02-88
Sear Spring
TA01135 Sear
STEP 2:
❏
Carefully install the left receiver half (make sure halves fit flush).
❏
Insert 4 short receiver bolts
.
❏
If marker has a barrel shroud
- insert it now.
❏
Insert 3 long receiver bolts
and
❏
tighten
the 7 bolts
/
.
❏
Attach adapter
tighten
2 bolts
(NOTE: short adapter
bolt goes in front).
❏
Apply marker oil onto the barrel o-ring, insert
the barrel
and carefully
screw it in.
❏
Slide the feed elbow
into the receiver and tilt up until the feed lock
holds it in place.
❏
E-Trigger
TM
Markers - Attach a 9 volt battery to the
battery connector and be sure the wires lay flat inside
the cutout area of the receiver.
❏
Carefully tilt and insert the battery (wire attached end
first
) into the receiver.
❏
Install the left receiver grip
with 2 bolts
.
❏
Press in the 2 magazine tabs
and slide the
magazine
up into the marker until the tabs lock
it in place. NOTE: The magazine may be used to
store tools and lubricating oil for your marker (shown
with 2 allen wrenches
and oil).
Reassembling Receiver Halves:
(continued on page 19)
❏
Double check that the E-Trigger
TM
parts
are positioned correctly for reassembly as
follows:
❏
1) Place solenoid / (armature - fits
inside solenoid) into right receiver.
❏
2) Carefully align and insert the
electronics board
into slot.
❏
3) Place trigger switch on two pins of
right receiver half.
❏
4) Insert capacitor in slot.
❏
5) Route wires in cutout areas to lay flat under armature pin and
battery and not be pinched when receiver halves are reassembled.
❏
Visually inspect internal wires for disconnected wire end(s) or damage.
❏
6) Insert armature pin
into 2 slots so it moves freely.
❏
7) Insert Magnet
in slot below armature as shown.
❏
Double check that all parts are in place as shown.
❏
Place battery connector
through left receiver half
❏
make sure
the magnet fits into left receiver half slot so it does not break and
❏
wires are not pinched as you
❏
place left half on right half so the
halves fit flush.
(E-Trigger
TM
Markers Go to STEP 2 on page 19).
Marker Disassembly / Assembly (continued from page 17)
Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when assembling.
Reassembling Receiver Halves: (continued from page 18)
6)
