manualshive.com logo in svg

TimeLine 71B008, Руководство по установке

Поделиться
Скачать
TimeLine 71B008 Скачать руководство пользователя страница 1

ECC NO. 1019 

Page 1

 

73630 REV. C 

 

Installation Guide 

Micro Lynx ACG Option Card 

TIMELINE VISTA, INC. 

1755 LA COSTA MEADOWS DRIVE, SUITE B 

SAN MARCOS, CA  92069 

 TEL. 760-761-4440 

(FAX 760-761-4449) 

[email protected]

 

DATE:

 

2/2/96

 

MODEL:

 

Micro Lynx

 

REVISION:

 

All

 

SERIAL NO:

  All

 

SOFTWARE:

  All

 

REQUIRED TOOLS: 

Static safe workstation 

Phillips screwdriver 

Grounding wrist strap 

1/4" Nut driver 

REQUIRED PARTS: 

TimeLine Part Number 71B008, ACG-1 Option Card, or 
TimeLine Part Number 71B009, ACG-2 Option Card 

PROCEDURE: 

1.  Turn off the power and place the Micro Lynx System Unit on a static safe 

workstation.  Ground yourself and the workstation anti-static mat. 

2.  On the back of the System Unit, remove the cover labeled 

AUDIO CLOCK GENERATOR

.   

3.  Remove the six phillips screws securing the top cover to the System Unit. 

4.  Position the System Unit so that the front panel faces you, and remove the top cover. 

 

Note:

 

 

Installation of the ACG Card is serial number dependent. For instructions on installing the  

ACG Card, go to the section of this installation guide covering your Micro Lynx System Unit 

serial number range  

 

Содержание 71B008










Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды