Timeguard LEDPROFOB RF Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

Timeguard LEDPROFOB RF Скачать руководство пользователя страница 4

3

• Transmission and Receiving Distance:

100m hand held (clear line of sight)
10m when mounted inside a wall switch
(recommended mounting height = 1.2m)

• Total number of fobs usable per PIR: 6
• Operating Temperature: -20°C to +40°C
• RF Module: TX Transmitter
• RF Frequency: 433.72MHz to 434.12MHz
• IP44 Rated suitable for restricted external

applications

• CE Compliant
• Dimensions (H x W x D): 60 x 38 x 15mm

4. Pack contents

• 1x LEDPRORFKB-WH Dedicated PIR Light Controller

c/w RF remote control for LEDPRO Floodlights

• 1x LEDPROFOB RF Remote Fob
• 1x Instruction Manual
• 1x 3V CR2032 Battery
• 1x Lens Sticker
• 2x Wire (for wall mounting a fob)

5. Selecting a Location

• The light controller has number of detection zones,

at various vertical and horizontal angles as shown
(see diagram A).

«
...
2
3
4
5
6
...
»

Содержание LEDPROFOB RF





















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды