Timberline Tool TR650 Скачать руководство пользователя страница 11

TIMBERLINE TR650

11

TIMBERLINE LIMITED WARRANTY

Warranty Policy

Every product manufactured by Timberline Tool is thoroughly inspected and tested before 
leaving the factory.  Our products are warranted to be free of defects from workmanship 
and materials for the period of ONE YEAR from the date of original purchase.  Should any 
trouble develop with our tools, handles, or accessories during this one-year period please 
call 800.735.6845 to obtain return authorization for repair.  If inspection shows the trouble 
is caused by defective workmanship or material, Timberline Tool will repair or, at our option, 
replace the product without charge.

This Warranty does not apply where:
• 

repairs have been made or attempted by others.

• 

repairs are required because of normal wear and tear.

• 

the tool has been abused, misused, or improperly maintained.

• 

alterations have been made to the tool.

IN NO EVENT SHALL TIMBERLINE TOOL BE LIABLE FOR ANY INDIRECT, INCIDENTAL 
OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT.  THIS 
DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.

TIMBERLINE TOOL DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUD-
ING IMPLIED WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC 
PURPOSE,” AFTER THE ONE-YEAR TERM OF THIS WARRANTY.

This Warranty gives you speci

fi

 c legal rights, and you may also have other rights which 

vary from state to state.  Some states do not allow the exclusion or limitation of incidental or 
consequential damages, so the above limitation or exclusion may not apply to you.  Some 
states do not allow limitation on how long an implied warranty lasts, so the above limitation 
may not apply to you.

Содержание TR650













Отзывы: