TiLite ZR Скачать руководство пользователя

Страница: 55 / 97

6-5

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 6: SIDE GUARDS

Figure 6-6

Mounting/Adjusting

Back

Mount

Coved

Washer

Saddle

Nylock Nut

Washer

Spacer

Seat

Tube

Front Cam

Conical Washer

Button Head

Cap Screw

Allen

Screw #1

Conical Washer

Rear Cam

Allen Screw #2

Adjusting

Tools Needed:

• 7/16” Open End Wrench

• 5/64” Allen Wrench

• 5/32” Allen Wrench

1. Using the 5/32” Allen wrench, loosen but do not remove Allen Screw #1. See Figure 6-6.

2. Place the 5/32” Allen wrench in Allen Screw #2 to hold it in place. Loosen the nylock nut using the 7/16” Open

End wrench.

3. Loosen but do not remove the eight Button Head Cap screws (four in each cam).

4. Adjust the side guard to the desired position, rotating the cams as needed and allowing the Allen screws to slide

within the cam slots.

5. Once the desired side guard position has been achieved, tighten the eight Button Head Cap screws (four on each

cam) using the 5/64” Allen wrench.

6. Using the 5/32” Allen wrench, securely tighten Allen Screw #1.

7. Keeping Allen Screw #2 in place using the 5/32” Allen wrench, securely tighten the nylock nut using the 7/16”

Open End wrench.

WARNING

The threads on the Button Head Cap screws and Allen Screw #1 that secure the cams to the cam covers and the

side guard to the back mount have been treated with Vibra-TITE® VC-3, a locking and sealing coating, to reduce the

possibility that they will become loose. You should be able to adjust the cams and/or sideguards approximately four

times without reapplying the coating to these screws. If you repeatedly adjust the cams or remove the sideguard,

TiLite requires that you reapply Vibra-TITE® VC-3 after every fourth adjustment.

If you ignore this Warning, you could

fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Содержание ZR


































































































Результаты поиска

Содержание ZR

Отзывы:

Похожие инструкции для ZR

Бренды по названию

Популярные бренды

TiLite ZR, Руководство пользователя

Результаты поиска

Содержание ZR

Отзывы:

Похожие инструкции для ZR

Бренды по названию

Популярные бренды