4
5
Cabling
Power Requirement (Mains)
TileVision
®
requires a 13 amp socket outlet connected to a 240 V mains supply via a
readily accessible isolation switch mounted in close proximity to the unit. This
electrical installation shall include an all-pole switch with a contact separation of at
least 3 mm in each pole, both the socket and pull switch must conform to the latest
safety specification and be protected via an RCCD device or similar. This socket must
be fitted in a dry area, away from any moisture (usually in ceiling).
The mains plug
should be fitted with a 5 amp fuse
.
TileVision
®
Power Supply (24 V)
Plug the power supply lead into the mains socket and plug the 24V transformer/power
supply onto the end of this mains lead.
The power supply is not waterproof and so must be positioned in a dry, well-ventilated
area away from any water or moisture. It is fitted with an integral 4 metre lead to feed
the TileVision
®
unit, this must not be cut, shortened, lengthened, etc. as this could
potentially damage the unit and also has implications regarding the unit’s safety.
Feed the cable from the power supply through a cable inlet into the TileVision
®
unit –
making sure that there is approximately 500 mm of slack at this end. Any spare cable
should be neatly coiled in a safe place, away from any water or heat generated from
lights, etc.
Please note –
All electrical installation should be carried out by a fully qualified
electrician and all fire & safety regulations should be obeyed.
Mains plug
240V mains supply
Isolation
pull switch
Mains power
supply cable
IEC320 socket
24V DC
power
supply
Integral power
supply cable (4m)
TV aerial cable
(not supplied)
Speaker
cable
Speakers
Mains socket
Installing the speakers supplied
For each speaker you should cut a
123 mm diameter hole and four 4.5 mm
holes in the ceiling using the template
supplied. Make sure not to cut through
any ceiling joists, cables, pipes, etc. This
hole should be no more than a 3 metre
cable run from the TileVision
®
unit.
A 3 metre length of 2-core speaker cable
is provided with the TileVision
®
unit and
this should be run from the TileVision
®
back box to the position of the speaker.
Feed one end of the speaker cable
through the second cable inlet, leaving
approximately 500 mm of slack in the
back box. All slack cable should be
pulled back and left in the ceiling area.
Connect the other end of the speaker
cable to the ceiling speaker by pushing the spade connector onto the appropriate
connector. Ensure the striped conductor is connected to the negative terminal and the
plain conductor to the positive terminal.
Fix the speakers to the ceiling using the screws and fittings supplied.
TV Aerial Feed
Take a 75 Ω feed (CT100 or similar quality cable) from your present television aerial or
distribution system and feed this into the TileVision
®
back box through the third cable
inlet. Terminate with a standard COAX termination. Ensure that the cable is not kinked.
Back box aperture protective cover
The back box is now correctly installed, please push the aperture cover provided into
the front of the back box (printed side outward) to protect the sealing flanges from
damage whilst awaiting the installation of the front assembly.
Speakers and Aerial Feed
☛
Note: The signal level fed to the set must be at
least 60dB/1millivolt or the picture may be noisy.
A TV Distribution Amplifier may be required if you
are in an area of weak signal or if other televisions
are already being fed from the aerial. If in doubt,
consult a qualified aerial technician.
Refer to pages 5 to 9 of the TileVision
®
Instruction
Manual for further information on speaker phasing
and additional connections for HDMI, S-Video,
Audio and SCART (full).
5" TEMPLATE
ø4.5mm
(
11
/
64
") HOLE
97mm (3
7
/
8
")
123mm (4
7
/
8
")
Template shown here at 50% actual size
