TIL TDFM-9200 Скачать руководство пользователя | Manualshive

Страница: 13 / 41

background image

TECHNISONIC INDUSTRIES LIMITED

TDFM-9200 Installation Instructions

TiL 13RE472 Rev. B

2-1

2.1

GENERAL

This section contains information and instructions for the correct installation of the TDFM-9200
Transceiver.

2.2

EQUIPMENT PACKING LOG

Unpack the equipment and check for any damage that may have occurred during transit. Save
the original shipping container for returns due to damage or warranty claims. Check that each
item on the packing slip has been shipped in the container.

2.3

INSTALLATION

The TDFM-9200 Transceiver is designed to be Dzus mounted and should be installed in
conjunction with an IN-9300 installation kit. See Figure 2.1 for an outline drawing of the unit with
dimensions to facilitate the installation.

2.4

INSTALLATION KIT – CONTENTS

The IN-9300 installation kit (P/N 129292) consists of:

1. One 25 Pin Cannon D mating connector (female) complete with crimp pins and hood.

2. Three 15 Pin HD Cannon D mating connector (female) complete with crimp pins and hood.

3. One 15 Pin HD Cannon D mating connector (male) complete with crimp pins and hood.

4. 4 BNC connectors.

2.5

ANTENNA INSTALLATION

The type and number of antennas depends on the model of transceiver being installed. The
following is a list of recommended antennas for the various RF modules:

VHFLO

30 to 50 MHz

Foxtronics Part # FLX-3050B or
Sensor Systems Part # S65-8282-34*

VHF AM

118 to 138 MHz

Comant Part # CI-292-1

VHF

136 to 174 MHz

Comant Part # CI-292-3

UHFLO

403 to 470 MHz

Comant Part # CI-275

UHFHI

450 to 520 MHz

Comant Part # CI-285

800

800 to 870 MHz

Comant Part # CI-306

800/700

764 to 870 MHz

Comant Part # CI-285

The antenna should be mounted on the bottom of the aircraft whenever possible. Consult with
instructions provided with the antenna. Connect the RF cables to the back of the transceiver
using the MALE BNC connectors provided in the installation kit. It is possible to use equivalent 50
ohm aviation antennas that cover the appropriate bandwidths.

SECTION 2: INSTALLATION INSTRUCTIONS

«
...
11
12
13
14
15
...
»

Содержание TDFM-9200










































Отзывы:

Нет отзывов

Похожие инструкции для TDFM-9200

Бренд: Balluff Страницы: 62

Бренд: Balluff Страницы: 105

DigitalFlow XGF868i

Бренд: Panametrics Страницы: 72

DigitalFlow XGF868i

Бренд: Panametrics Страницы: 90

Бренд: Ebyte Страницы: 15

Бренд: Watkins Johnson Страницы: 9

IMPERIAL HD 2 basic

Бренд: DigitalBox Страницы: 96

Бренд: Jung Страницы: 5

Бренд: Ceragon Страницы: 63

TRANSDUCER MOUNTING PROCEDURE - SCHEMA REV B

Бренд: Simrad Страницы: 1

Бренд: Trango Systems Страницы: 8

Бренд: M-system Страницы: 3

Бренд: Strong Страницы: 20

Бренд: Olin Страницы: 14

Бренд: HiTV Страницы: 28

Бренд: DRAKE Страницы: 48

Бренд: Aqua Quip Страницы: 6

Бренд: Igema Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды