Tiger WILDKAT JD6105-25E T4F Скачать руководство пользователя страница 32

Страница: 32 / 240

ASSEMBLY

Assembly Section 2-2

Before attempting to mount your Tiger mower, it is important

to read and understand all of the safety messages in the Safety
Section of this manual.

Check complete shipment list against the packing list to make sure there are no

shortages. Make certain the tractor model is the appropriate one for the mower received!

Always use a floor jack, hoist or fork lift to lift and raise heavy parts.

Read and understand the entire Assembly Section instructions before attempting to mount

your Tiger mower. Refer to the Parts Section of this manual for detailed illustrations to locate all
parts.

(ASM-C-0001)

TRACTOR PREPARATION

Remove right and left hand steps.

Disconnect battery cables from both batteries.

Remove engine side panels, or raise hood to access front pulley.

Remove plugs from tractor casting where mainframe and pump mount will be attached.

Remove any front weights and weight supports.

Raise the tractor onto jack-stands and remove the right and left rear wheels.

(ASM-JD-0001)

CRANKSHAFT ADAPTER

For JD6xxxD tractors with a front pump mount, install the John Deere pulley kit P/N:

LVB24989 and follow the instructions.

(ASM-JD-0250)

Содержание WILDKAT JD6105-25E T4F

















































































































































































































































Результаты поиска

Содержание WILDKAT JD6105-25E T4F

Отзывы:

Похожие инструкции для WILDKAT JD6105-25E T4F

Бренды по названию

Популярные бренды

Tiger WILDKAT JD6105-25E T4F, Руководство пользователя

Результаты поиска

Содержание WILDKAT JD6105-25E T4F

Отзывы:

Похожие инструкции для WILDKAT JD6105-25E T4F

Бренды по названию

Популярные бренды