Tiger SIDE ROTARY Скачать руководство пользователя страница 47

Страница: 47 / 178

Assembly Section 2-17

ASSEMBLY

DECK MOUNTING AND LIFT ASSEMBLY

Install the upper sheave bracket on the outboard cylinder and tighten securely

against piston rod shoulder. Tighten the set screw, and align the draft beam.

Install the lower sheave bracket on the draft beam with a ¾” cap-screw and two

hex nuts as shown in the diagram on the next page.

Align the deck with the draft beam mounting hole and install the outer draft beam

pin. Align the holes in the draft beam pin with the holes in the boss and secure with
cap-screw, lock-washer and hex nut.

Pass the lift cable through upper sheave bracket and attach to turn buckle with

turn buckle pin and cotter key. Attach turn buckle to draft beam with turn buckle pin
and cotter key.

Place the cable in the upper sheave bracket with the cable on top of the wheel.

Secure wheel with sheave pin (with grease zerk) and R-clip. Place lift cable in lower
sheave below the wheel and install sheave with pin (with grease zerk) and R-clip.
Then install the

The cable can now be attached to the deck mounting bracket with the shackle.

Tighten shackle pin securely. NOTE: DO NOT tighten the turn buckle at this
time!

Содержание SIDE ROTARY



















































































































































































Результаты поиска

Содержание SIDE ROTARY

Отзывы:

Похожие инструкции для SIDE ROTARY

Бренды по названию

Популярные бренды

Tiger SIDE ROTARY, Монтаж и эксплуатация

Результаты поиска

Содержание SIDE ROTARY

Отзывы:

Похожие инструкции для SIDE ROTARY

Бренды по названию

Популярные бренды