Thank you for purchasing a “TIGER” Stainless Steel Mug.
Please read the instructions completely before use.
Keep these instructions for future reference.
Instructions
Stainless Steel Mug
MMW-A
MODEL
Make sure that all parts are present before use.
1
2
3
Lid
Outer
stopper
Inner
stopper
Stopper
Stopper
unit
Stopper gasket (large)
Stopper gasket (small)
Spout
Body
Protective sheet
(attached to the outside bottom)
Capacity
Heat retention
Cold retention
0.36 liters / 12.2 oz
Greater than 86°C •187°F (1hour)
Less than 8°C •46°F (6hours)
Greater than 67°C •153°F (6hours)
0.48 liters / 16.2 oz
Greater than 87°C •189°F (1hour)
Less than 7°C •45°F (6hours)
Greater than 71°C •160°F (6hours)
0.6 liters / 20.2 oz
Greater than 89°C •192°F (1hour)
Less than 7°C •45°F (6hours)
Greater than 75°C •167°F (6hours)
For the purpose of performance improvement, designs, specifications and parts shown in this
publication are subject to change without notice.
Important!
Keep out of reach of children.
Do not let children play with the
product.
Noncompliance to these
instructions may result in scald
or injury.
Do not use the product if its
ability to retain heat declines.
Hot beverage can make the
product very hot, potentially
causing burns.
Do not use the product for any
purpose other than keeping bev-
erages warm or cold.
Keep the product in an upright
position at all times.
Do not leave the product in the
bag for a long time.
Wipe off any liquid left
around the rim of the bottle
after drinking.
Do not knock over, drop or
expose the product to
excessive shocks.
Do not put dry ice or carbonated
beverages in the product.
Do not store milk, dairy
products, or certain fruit juices
in the product.
Do not place the product near
stoves, open flames, or other
sources of extreme heat.
Do not heat the product in a
microwave oven.
Be sure to set the stopper in
proper position.
Do not fill the product above
the maximum level shown
below.
Be
v
erage
Maximum
le
v
el
Approx.
1cm
•
1/2-inch
Do not disassemble or
attempt to repair the product
by yourself.
Be sure to clean the product
immediately specially after
sports drink.
Do not use chlorine-based
bleaches or acetic acid
solutions when cleaning the
product.
Do not remove the protective
sheet on the underside of
the product.
To keep your beverage warm or cool longer.
Pour hot (or cold) water into the body, and let it sit for one or two
minutes to allow the inside of the body to heat (or cool).
Discard the hot (or cold) water after preheating (or precooling).
Clean after every use.
Use mild kitchen detergent.
Use a sponge or soft cloth.
Be sure to clean the stopper and gasket with every use.
Be sure to wipe off with dry cloth.
Do not place in a dishwasher/dryer.
The product rattles when shaken.
This is caused by a metal sheet moving inside the product that is used for boosting heat retention.
Replacing and Purchasing Consumable Parts
The stopper, spout and gaskets are consumable parts. Check once a year for damage/deterioration.
If heavily stained or loose, replace them.
For replacement parts, contact customer service or the shop where you purchased this
product.
Before contacting customer service
The utmost measures have been taken to ensure the quality of this product. However,
should the product be defective, contact your dealer and provide the following information.
1. Product name
3. Description of trouble (As detailed as possible)
2. Model Number 4. Purchase date
Feel free to send any questions or comments about this product to the shop where you purchased it.
Specifications
Heat retention has been calculated under the condition of adding hot water at 95°C ±1°C •
203°F±2°F and leaving it in a room temperature of 20°C±2°C • 68°F±4°F for 1hour or 6hours.
Cold retention has been calculated under the condition of adding cold water at 4°C ±1°C •
39°F±2°F and leaving it in a room temperature of 20°C±2°C • 68°F±4°F for 6hours.
Capacity is the actual volume of water that can be stored into the product when the stopper is
closed. This is not the “Maximum level” volume described in “Safety Precautions”.
Consume beverage within the
day to prevent from spoiling.
Drink slowly when the product
contains a hot beverage.
Safety Precautions
Safety Precautions
If adding salty foods or
liquids, wash immediately
after consuming.
MMW
-A
TIGER HANBAI (H.K.) CO.,LTD.
Rm. 1006
B,
10
/FI., J
oin-in Hang Sing Centre
, 71
-
75
Container Port Road
,
K
wai
Chung
,
N.T.
Tel:
(852)
2418-091
2
F
ax:
(852)
2418-09
11
JAPAN TIGER CORPORATION OF U.S.A.
2730
Monterey Stree
t, S
uite
105
Torrance
,
CA
9050
3
Tel:
(310)
787-1985
F
ax:
(310)
787-198
6
EMAIL: [email protected]
TIGER CORPORATION
Head Of
fice: 3-1 Hayamicho, Kadoma Cit
y
, Osaka 571-8571, Japan
URL : http://www.tiger.jp/global.html
How to Use
How to Use
Attaching and removing the stopper
Lid
Inner stopper
Outer stopper
Body
Outer stopper
Groove
Protrusion
Attaching and removing the stopper gasket
Attach the stopper
to the proper position and direction.
When attaching the stopper gasket, make sure to fit it
completely onto the inner lid while checking the direction.
Stopper gasket (large)
Stopper gasket (small)
Side without groove
Protrusion
Concave section
To remove
To attach
Loosening
direction
Loosening
direction
Closing
direction
Align the height of the
outer and inner stoppers.
Closing
direction
Attach the stopper gasket to the proper position and direction.
Align the protrusion
of the stopper
gasket (large) with
the concave
section of the inner
stopper.
How to Clean
How to Clean
