Tiger JD6175R Скачать руководство пользователя | Manualshive

Страница: 53 / 236

background image

OPERATION

Boom

Operation Section 3-3

©2013 Alamo Group Inc.

OPERA

TION

1.OPERATOR REQUIREMENTS

Safe operation of the unit is the responsibility of a qualified operator.  A qualified operator has read and
understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor
operation and all associated safety practices.  In addition to the safety messages contained in this manual,
safety signs are affixed to the implement and tractor.  If any part of the operation and safe use of this
equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely understand the operation of the
equipment, it is the responsibility of the supervisor to read and explain the manuals, safety practices, and
operating instructions to the operator.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment (PPE)
for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is designed to
provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

•

Always Wear Safety Glasses

•

Hard Hat

•

Steel Toe Safety Footwear

•

Gloves

•

Hearing Protection

•

Close Fitting Clothing

•

Respirator or Filter Mask (depends on
operating conditions)

(OPS-U- 0002)

NEVER use drugs or alcohol immediately before or while operating the
Tractor and Implement. Drugs and alcohol will affect an operator’s
alertness and coordination and therefore affect the operator’s ability to
operate the equipment safely. Before operating the Tractor or Implement,
an operator on prescription or over-the-counter medication must consult
a medical professional regarding any side effects of the medication that
would hinder their ability to operate the Equipment safely. NEVER
knowingly allow anyone to operate this equipment when their alertness or
coordination is impaired. Serious injury or death to the operator or others
could result if the operator is under the influence of drugs or alcohol.

(SG-27)

«
...
51
52
53
54
55
...
»

Содержание JD6175R













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JD6175R

Бренд: PAJ Страницы: 95

Бренд: Navibe Страницы: 8

Бренд: Varta Страницы: 2

Бренд: Eaton Страницы: 11

Бренд: Zetor Страницы: 108

Бренд: Warrior Products Страницы: 4

Бренд: Neuspeed Страницы: 2

Бренд: Empire Comfort Systems Страницы: 4

Бренд: Curt Manufacturing Страницы: 6

Бренд: IMV Страницы: 8

Бренд: ooma Страницы: 27

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Бренд: Soehnle Страницы: 20

Бренд: PASCO Страницы: 4

Бренд: Amazon Страницы: 100

TRIUMPH Bonneville T 120

Бренд: hepco & becker Страницы: 4

Бренд: Peg-Perego Страницы: 28

AVID DISC BRAKES

Бренд: Avid Technology Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды