TiEmme GLH110, Руководство пользователя, Страница: 3 / 15

Pag. 3/15
0CAR6IN019124_Manual_GLH110_Rev_0.3
PUMP P1 FUNCTIONING TEST
When the controller is OFF, prolongued pressure of K3 key:
 P1 output is activated for as long as the key is pressed and the display will show tSt1
PUMP P2 FUNCTIONING TEST
When the controller is OFF, prolongued pressure of K4 key:

P2/P4 output is activated for as long as the key is pressed and the display will show tSt2
SERVICE OUTPUT
P4 SERVICE output is programable from the Installer MENU by using parameter P06 :

P06 = 0 DISABLED : the output does not work.

P06 = 1 THERMOSTAT : the output is activated if the temperature of S1 probe is above Thermostat A09.
 P06 = 2 GRILL : press K1 key to turn on/off the output.
 P06 = 3 AIR DAMPER : this output is used to manage an Air Damper to adjust for Combustion Air Flow.
AIR DAMPER
To make use of the Air Damper function set parameter P06 = 3
If the output is ON the Air Damper will be Open, if the output OFF the Air Damper will be closed.
The Air Damper will stay Open as long as the temperature of S1 probe is below A05 Thermostat. The Air Damper will close
when the temperature is above this Thermostat.

If P12 = 1 the Start Manual function is enabled:
If S1 Temperature is below A01 , the Air Damper will Close. During the Ignition phase of the Fireplace, by pressing K1 key
the Air Damper will Open manually (the output corresponding Led will flash). When the Temperature falls below A01 ,
Thermostat after t06 time the Air Damper will close automatically.
PROBE TYPE
The controller can manage NTC10K, NTC100K and PT1000 type of probes, which can be configured by using parameters
P01 , P02 , P03 and P17 of the Installer MENU.

Fireplace Probe: P01 = 0 → NTC10K; P01 = 1 → NTC100K; P01 = 2 → PT1000

DHW Boiler Probe/ Tall Buffer : P02 = 0 → NTC10K; P02 = 1 → NTC100K; P02 = 2 → PT1000

Short Buffer Probe:
P03 = 0 → NTC10K; P03 = 1 → NTC100K; P03 = 2 → PT1000

Ambient Probe:
P04 = 0 → NTC10K; P04 = 1 → NTC100K; P04 = 2 → PT1000

Manifold Probe: P17 = 0 → NTC10K; P17 = 1 → NTC100K; P17 = 2 → PT1000
S3 INPUT CONFIGURATION
Parameter P05 can be enabled to mange the following:

P05 = 0, S3 input = DISABLED

P05 = 1, S3 input = PRESSURE SENSOR

P05 = 2, S3 input = AMBIENT SENSOR

P05 = 3, S3 input = AMBIENT SENSOR
PRESSURE SENSOR
If P05=1 pressure sensor management is enabled on probe S3 .
If P07=1 pressure sensor errors are enabled:

If Water Pressure < Pr1 dispaly shows PrLo + audible signal.

If Water Pressure > Pr2 dispaly shows PrHi + audible signal.
PROBE SENSOR/AMBIENT THERMOSTAT
Parameter P05 can be setup to enable the management of the Probe Sensor/Ambient Thermostat

If the Ambient Temperature S3 > b01 or the Ambient Thermostat is Open (
Led flashing
) and there is NO DHW request

The Shutter is closed
The hydraulic/plumbing plants with a Buffer tank; if the Ambient Temperature is S3 > b01 or the Ambient Thermostat is
Open the Heating Pump will be turned off (deactivated)
SHOWER
( P13=1) if used in specific hydraulic/plumbing plants where it is required, it can be enabled by pressing K2 key for 3 sec :


The display shows T03 time (minutes) giving (DHW) Domestic Hot Water priority;
 K3
and
K4
keys increase /decrease the duration

Wait 5 seconds to save and exit from this setup.

To exit without saving press K1 key.
T03 time is signaled by led flashing, giving priority to DHW production based on the type of hydraulic/plumbing plant
in use.
This function is over when

T03 time has expired.

By pressing again K2 key

If the temperature of S1 Probe is greater than A07 Safety Thermostat:
And T03=0 , the shower function can be disabled by pressing K2 key.