Wireless Barcode Scanner
Quick Guide
Reset to Defaults
VER: TS45_QG_EN_V1.01
Handset & Cradle
A Handset
①
Data Indicator (Front)
②
Power Indicator (Back)
③
Trigger
④
View window of capture
B Cradle, data relay and charging handset
⑤
Indicator
⑥
Pairing Button
⑦
Channel Button
⑧
Data & Power Interface
Installation
Step 1.
Refer to the below pictures, firstly connect the cradle
⑧
to
host (e.g. PC or POS) with cables of different interface
：
USB
:
Plug the RJ45 into cradle
⑧
, and plug the male USB into the host.
USB cable
Keyboard
PS/2:
Plug the RJ45 to cradle
⑧
, and connect the male PS/2
end to host port and the female end with keyboard wire.
PS/2 cable
RS232
：
Plug the RJ45 into cradle
⑧
, plug the RS232 end to the host.
The DC power should be plugged into the RS232 connector.
RS232
cable
Typically, the cradle will auto identify the interface (COM) type. In
extreme cases cradle may need a manually setting if the host fails to
identify it. Please scan the code below for manual setting.
Automatic Identification (Default)
USB
Keyboard PS/2
RS232
Note: The auto setting of interface type will only be activated when
the pairing is well done. Please refer to the Step2 and Step3 for pairing.
Step 2.
Place the handset onto the cradle to pair them. Press and hold
cradle
⑥
until the handset issued a "beep-beep-beep" sound. The
pairing is done.
Note: 1.One cradle can support maximum 100 handsets. The handsets
cannot upload data if they are not well paired. 2. If a U-key receiver is
in use, please scan the barcode on the key for pairing. A “beep-beep-beep”
sound means pairing is done.
Usage of Scanner
Power On/Power off
When trigger (handset
①
) is pulled and a Beep-Deep sound comes out,
the handset is power on. If handset is not used for 30sec (default), the
handset will auto turn off. The timing can be reset to your need.
Code capture
In the standby mode, pull the trigger to capture code. Make sure the
red aiming line
is correctly covering the full code.
Correct way Incorrect way
Recharging
Way 1, Place the handset onto the cradle to start recharging.
Way 1 Way 2
Way 2, Using USB DC adapter or USB ports on PC as the power source,
it can be charged by Micro USB cable via interface at the handset bottom.
Note
：
1. When the handset is low power, the power indicator
②
will be
flashing green. 2. When the handset is recharging, the power indicator
keeps flashing red, and it turns yellow on when charging finishes.
Built-in Data Memory
In Auto-storing Mode, if the handset is out of limit to wireless contact
radius with the cradle, the captured code data will be saved into built-in
memory of handset and the data indicator
①
turns red on. The handset
will upload the code data to the cradle automatically when the wireless
connection gets back normal. Then the data indicator
②
turns green.
Multi-Cradles working
In case two or more cradles working in the same room, please set
them to different channels to ensure high efficiency upload as follow.
1. Open a notepad or any text editor on the host and press the Channel
Button
⑦
to change the channel number. The channel No. can be
displayed like the barcode on the notepad etc.
2. Place the handset onto the cradle. Repair them to get new channel.
Remark: If two or more cradles working in the same signal channel, it
will slow down upload speed. However, they won’t jam with each other.
Indicator & Button
Scanner Indicator
Indicator
state
Meaning
Power
Indicator
(
②
Back)
Green on
Started normally
Green flash
Power low, need to recharge
Red flash
Recharging
Yellow on
Recharge finished
Data
indicator
(
①
Front)
Green on
All data uploaded
Red on
Stored data pending to upload
Red flash
Data storage is full
Yellow flash
Data is uploading
Possibility of upload failures: Cradle disconnected to PC; Out of limit to
contact radius; Handset working in Manual Upload Mode (stock check).
Cradle Indicator
Light
Meaning
Green
Flashing: Identifying interface
On: Interface is identified
Red
Flashing: Receiving code data
On: Stored data pending to upload
Cradle Button
Button
Position
(mark)
Function
Pairing
Button
⑥
Left
Press and hold it 4 seconds to pair the
handset and cradle. A “Dee-Doo-Dee”
means pairing finishes.
Channel
Button
⑦
Right
Setting signal channel. One press for one
channel No. up.
①
②
③
⑤
⑥
⑦
④
⑧
□
A
□
B
TI4145
