THUNDER TIGER Raptor 50 V2 kit Скачать руководство пользователя страница 9

Страница: 9 / 42

(3) HMV740ZZ

(4) BK0077

(5) BK0079

(6) BK0075

(7) BK0015

(8) BK0016

(9) BK0014

(1) HMJ2-10N

(2) HMC3-10B

(3) HMV740ZZ

(1) HMJ2-10N

(8) BK0016

(3) HMV740ZZ

(5) BK0079

(6) BK0075

(3) HMV740ZZ

(4) BK0077

(2) HMC3-10B

(7) BK0015

4 Main Drive Gear Assembly

(1) HMC3-8B Socket Screw (M3x8)............. 4

(2) HMQ14 Snap Ring.................................... 2

(3) BV0033 One Way Clutch Housing.............1

(4) BK0148 Main Spur Gear 85T.....................1

(5) BK0610 Autorotation Tail Drive Pulley ..... 1

(6) BK0034 One Way Clutch Shaft..................1

5 Washout Assembly

(1) HMJ2-10N Self Tapping Screw(M2x10).. 2

(2) HMC3-10B Socket Screw (M3x10)......... 2

(3) HMV740ZZ Bearing (d4xD7xW2.5)........ 4

(4) BK0077 Collar ........................................ 2

(5) BK0079 Pin............................................. 2

(6) BK0075 Linkage Ball.............................. 2

(7) BK0015 Flybar Control Lever.................. 2

(8) BK0016 Washout Linkage ..................... 2

(9) BK0014 Washout Base............................1

Make sure Linkage Balls are attached to the
inside hole of each stabilizer control lever.

(1) HMC3-8B

(6) BK0034

(2) HMQ14

(5) BK0610

(4) BK0148

(2) HMQ14

(3) BV0033

Add a drop of Blue Locktite on the
thread of each of these four screws.

Add some light
weight oil before
inserting this into
BV0033

Содержание Raptor 50 V2 kit











































Результаты поиска

Содержание Raptor 50 V2 kit

Отзывы:

Бренды по названию

Популярные бренды

THUNDER TIGER Raptor 50 V2 kit, Руководство пользователя

Результаты поиска

Содержание Raptor 50 V2 kit

Отзывы:

Бренды по названию

Популярные бренды