THUNDER TIGER 4756, Инструкция по эксплуатации

Страница: 27 / 50

-26-
Swashplate Type Setting /
十字盤模式設定
120°
120°
120°
Before starting, make sure the following preparation is done.
1. Set all trims, knobs, and switches to the neutral and zero position.
2. Reset the radio to its factory preset position.
3. Choose the 120°E-CCPM swashplate control mode.
Please refer your Transmitter manual to find a proper setting.
Nose / 機首方向
開始設定之前，請先確認下列注意事項
1. 發射機上所有的調整旋鈕、機構均位於中立點。
2. 重新設定原廠內建數據。
3. 選擇E-CCPM 120°模式。
請參閱遙控器說明書，進行設定。
For safety, please ensure the motor has been deactivated and will not drive the main rotor head before
performing following setting processes. You may just unplug 2 of the wires from the motor and the ESC or move
the motor with pinion away from the main gear to avoid a rotating rotor head.
安全起見，執行下列設定程序時，請確認馬達不會驅動主旋翼頭。您可拔除馬達與速控器間任兩條連接線，或將馬達驅動齒
與主齒盤脫離。
Warning! /
警告!
Radio System Setup /
遙控系統設定
Electric Device Connection /
電子設備連接說明
CH1 CH2 CH3 CH4 CH5 CH6 AUX 1 (Batt)
7 channel receiver
七動作接收器
Gyro
陀螺儀
Batteay of receiver 4.8-5.8V
接收器電池 4.8-5.8V
ACE RC / FUTABA / HITEC Radio Sysym JR Radio Sysym
ESC
速控器
Aileron
左右/副翼
Elevator
前後/升降舵
Rudder
尾舵
Pitch
螺距
CH1 CH2 CH3 CH4 AUX 1 AUX 2 Batt
7 channel receiver
七動作接收器
Gyro
陀螺儀
Batteay of receiver 4.8-5.8V
接收器電池 4.8-5.8V
ESC
速控器
AUX1 (CH6) / CH2* CH6 / CH1* CH1 / CH6* CH2 / AUX1 (CH6)*
CH3
CH2
Gyro Gain Wire Gyro Gain Wire
陀螺儀訊號線
Aileron
左右/副翼
Elevator
前後/升降舵
Rudder
尾舵
Pitch
螺距
*CH2 & Aux1(CH6) are
Interchangeable
*CH2 & Aux1(CH6) 可互換
*CH1 & CH6 are
Interchangeable
*CH1 & CH6 可互換
E-CCPM system requires 3 channel for aileron, elevator and an AUX(for pitch). But people may get confused because
the 3 channels are not referred to any independent movement. They are operated together to carry out the rolling,
flipping and collective controlling. As a result, the following connecting manner is recommended.
The following chart is the E-CCPM connecting for your reference. Please also consult your radio instruction manual.
E-CCPM系統需要使用三個通路予副翼、升降舵、與螺距（使用AUX通道）。許多愛好者可能會對於此設定感到困惑，但是在混控
模式下，必須藉由三顆伺服機同時完成動作，因此建議依照下列說明完成伺服機與接收機連結。
下列圖示為安裝範例，實際接線方式，請參照您的遙控器使用說明書。
All manuals and user guides at all-guides.com