background image

3

PRE-ASSEMBLY NOTES

1. Please assemble your model according to this

instruction manual.  Do not attempt to modify or change

your Super Cub in any way as doing so may adversely

change its flying characteristics.

2. For Ready To Fly ( Super Combo) version, some

assembly steps are finished by factory craftsman.  We

recommend you to read the manual to familiarize

yourself with the airplane.

3. Before you begin please check entire contents of this

kit against the parts list and parts drawings to be sure

that no parts are missing or damaged.  This will also

help you to become familiar with each component. 

4. If you find that any par ts are either missing or

damaged, please contact with your dealer immediately

for replacement. Note: Your dealer cannot accept kits

from return if construction has begun.  

e-mail:[email protected]

Remember we have worked very hard to make this model

as easy to assemble as possible while still maintaining our

high standard of quality.  Your assembly of this model is

ver y  impor tant and will determine the final flight

capabilities of your Super Cub, so use extra care and

follow the assembly procedure exactly.

OTHER ITEMS REQUIRED

Radio: You will need at least a 3

channel radio control system with 2

micro servos for your Super Cub.

3

2

ACE

8304

@?he

?J5?he

W.Y?he

?W.Yhf

?7H?hf

J5hg

?W.Yhg

W.Y?hg

7H

?J5?

W.Y?

?W.Y

?7H?

J5

?W.Y

W.Y?

7H

?J5?

W.Y?

7H

?J5?

?.Y?

ACE

8305

ESC-10:  ACE ESC-10 ( P/N

ACE8015) with BEC for controlling

the power of your Super Cub as well

as eliminating the need of a

separate radio battery. The BEC(

Battery Eliminator Circuitry) in this

controller will automatically turn off

the power to the motor when the

battery reaches a factory present

discharge level leaving about 10 minutes of flight time for

the radio system.

10A

BEC

ACE 8015

Battery:  We  recommend the use of

a 7 cell 8.4V 600mAh AAA size

NiMH battery ( P/N ACE2924)

8.4V 600mAh AAA size

ACE 2924

Charger: You will need a quick

charger to charger your power

batter y.  We recommend our

economical DC Quick Filed Charger

(P/N 

ACE 2604AC/B

).

12V

900mAh

ACE 2604AC/B

TOOLS AND SUPPLIES NEEDED

Mixing Stick for Epoxy  

Medium Grit Sandpaper  

Rubbing Alcohol  

Paper Towel  

Hobby Knife  

1/16” drill bit 1.5mm 

Ruler

Pen, Pencil or Marker  

Small Screw Drivers  

Scissors  

Needle Nose Pliers  

ACE 8304  3ch Single

Stick Radio

ACE 8305  3ch

Dual Stick Radio

No.8117  Micro Servo

Содержание 4315-Y

















Отзывы: