Thrane&Thrane TT-3042D Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 31

Thrane&Thrane TT-3042D Скачать руководство пользователя страница 14

11

Description

Description

1.2

1.2

Detailed description

Detailed description

Page

Page 44

7Jul98

7Jul98

Up to 7 Remote Alarm units with different Arcnet address setting
can be placed on various locations onboard ship, all connected
to one Capsat transceiver with the Arcnet.

EGC SafetyNet messages are routed to all Remote Alarm printers
connected. If no Remote Alarm is equipped with a printer or
Remote Alarm printer fail, the EGC Safetynet message is routed
to transceiver printer, computer printer or stored in disk.

The build-in printer can be configured for 40 or 80 chars/line,
automatic word wrapping is performed on long lines.

When printing at 40 chars/line the TT-3042D perform
papersaving compression on incoming data by stripping
leading spaces and by allowing a maximum of two succeeding
blank lines.

The build-in printer can be configured for bottom-to-top printing
and automatic page breaking to allow printouts to be read
directly from paperstrip at printout.

The build-in printer is maintenance free, printing on 112 mm
(4.4") width thermal paper rolls of length 24 meters. A build-in
paper detector indicates when paper is low. The printer is
temperature compensated to give equal printing quality over a
wide temperature range. Paper loading is eased by extended
feed length on paper empty condition.

Indicator and text background light level is selected by front
panel operation.

The TT-3042D is equipped with remote turn-on for power saving
configurations. Remote turn-on is enabled by jumper setting.

«
...
12
13
14
15
16
...
»

Содержание TT-3042D
































Отзывы:

Нет отзывов