manualshive.com logo in svg

THORLABS TPZ001, Руководство пользователя

Поделиться
Скачать
THORLABS TPZ001 Скачать руководство пользователя страница 42

42

HA0143T Rev 12K Sept 2015

Chapter 6

6.2.2 Control Tab 

Fig. 6.1 Piezo Settings panel

Feedback Loop Settings 

Loop mode

 - This panel can be used to select between the two distinct

operating modes: open loop and closed loop. Note that closed loop operation
is only possible if an external position reader (such as the TGS001 Strain
Gauge Reader) is used in conjunction with the piezo cube.

When the T-Cube Piezo Driver is used in conjunction with the T-Cube Strain Gauge
Reader unit (TSG001) on the T-Cube Controller Hub (TCH002), high precision closed
loop operation is possible using the complete range of feedback equipped piezo
actuators available from Thorlabs.

Caution

If the Piezo Driver is switch to closed loop mode without being connected 

to a Strain Gauge Reader, the piezo driver will expect a feedback signal 

and the piezo drive voltage will ramp up to the maximum limit. If the limit 

is set to 75V, a protective circuit limits the voltage to 75V. If 100V or 150V 

is selected, the output will ramp to 150V.

Содержание TPZ001





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды