THORLABS MCLS1-980-20, Быстрый старт

Страница: 2 / 7

Thorlabs.com - 4-Channel Fiber-Coupled Laser Source
http://www.thorlabs.com/newgrouppage9_pf.cfm?guide=10&category_id=19&objectgroup_id=3800[2/12/2016 5:39:20 PM]
available to modulate the laser diodes' outputs with an externally generated waveform. To prevent damage, the microcontroller will disable the output if the
sum of the analog input and internal set point exceeds the laser limits.
Safety
While most output sources fall within the class 3R laser rating, the system was fully designed to meet laser class 3B requirements. There is an interlock
located on the rear panel that must be shorted in order for any laser output to be enabled. This can easily be configured to be triggered by doors to disable the
lasers in unsafe conditions. The power switch is a keylock system to prevent accidental or unwanted use. Each source has its own enable button allowing the
user to choose the light source or sources he wishes to be active, as well as a master enable that must also be set. Each channel includes a green LED
indicator to easily determine its current state. There is a 3 second delay before the lasers turn on, and the user is warned by the LED rapidly blinking. The
laser must be turned off before connecting or disconnecting a fiber to the output ports, particularly for powers above 10 mW.
In the Box
The MCLS includes a universal power supply allowing operation over 100 - 240 VAC without the need for selecting the line voltage. The fuse access is
conveniently located on the rear panel. This unit is supplied with a U.S. line cord as well as a standard European line cord, the pre-configured MCLS1 with all
selected lasers installed, and the manual.
Below is a list of available lasers listed by wavelength and showing the corresponding minimum output power and pigtail fiber type. To discuss potential custom
wavelengths and configurations not available below, please contact Technical Support. Please use the configurator below to select the pigtails and locations
you would like.
Note: An MCLS1 unit must be purchased with at least one pigtail installed. If you leave a channel blank, the unit will be shipped
without a laser in that channel. Thorlabs will fill the empty slot at a later date if you desire. Please contact Tech Support prior to sending your unit
back to us.
Item #
Typical λ
Wavelength Range Minimum Power
a
Typical Power Laser Type Fiber
MCLS1-405-30
405 nm 400 - 410 nm 24.0 mW 28 mW Fabry-Perot S405-XP
MCLS1-406
406 nm 395 - 415 nm 4.0 mW 6 mW Fabry-Perot S405-XP
MCLS1-473-20
473 nm 468 - 478 nm 15.0 mW 20 mW Fabry-Perot 460HP
MCLS1-488
488 nm 483 - 493 nm 18.0 mW 22 mW Fabry-Perot 460HP
MCLS1-520
520 nm 515 - 530 nm 8.0 mW 10.0 mW Fabry-Perot 460HP
MCLS1-635
635 nm 630 - 640 nm 2.5 mW 3.5 mW Fabry-Perot SM600
MCLS1-638
638 nm 628 - 648 nm 10.0 mW 15 mW Fabry-Perot SM600
MCLS1-642
642 nm 635 - 645 nm 15.0 mW 20 mW Fabry-Perot SM600
MCLS1-658
658 nm 648 - 668 nm 9.5 mW 14 mW Fabry-Perot SM600
MCLS1-660
660 nm 653 - 663 nm 15.0 mW 17 mW Fabry-Perot SM600
MCLS1-670
670 nm 660 - 680 nm 1.5 mW 2.5 mW Fabry-Perot SM600
MCLS1-670-4
670 nm 660 - 680 nm 4.0 mW 5 mW Fabry-Perot SM600
MCLS1-685
685 nm 675 - 695 nm 10.0 mW 13.5 mW Fabry-Perot SM600
MCLS1-705
705 nm 695 - 715 nm 10.0 mW 15 mW Fabry-Perot SM600
MCLS1-730
730 nm 720 - 740 nm 12.5 mW 15.0 mW Fabry-Perot SM600
MCLS1-785
785 nm 770 - 800 nm 6.0 mW 7.5 mW Fabry-Perot 780HP
MCLS1-785-25
785 nm 780 - 790 nm 20.0 mW 25 mW Fabry-Perot 780HP
MCLS1-808-20
808 nm 803 - 813 nm 20.0 mW 25 mW Fabry-Perot SM800-5.6-125
MCLS1-830
830 nm 820 - 840 nm 8.0 mW 10 mW Fabry-Perot SM800-5.6-125
MCLS1-850
850 nm 840 - 860 nm 7.5 mW 10.5 mW Fabry-Perot SM800-5.6-125
MCLS1-850-MM
850 nm 847 - 857 nm 45.0 mW 50 mW Fabry-Perot GIF625
MCLS1-852
852 nm 847 - 857 nm 20.0 mW 25 mW Fabry-Perot SM800-5.6-125
MCLS1-905-20
905 nm 900 - 910 nm 15.0 mW 20 mW Fabry-Perot SM800-5.6-125
MCLS1-940
940 nm 930 - 950 nm 25.0 mW 30 mW Fabry-Perot SM800-5.6-125
MCLS1-980
980 nm 965 - 995 nm 6.0 mW 9 mW Fabry-Perot 980HP
MCLS1-980-20
980 nm 975 - 985 nm 20.0 mW 25 mW Fabry-Perot 980HP
MCLS1-1064
1064 nm 1059 - 1069 nm 20.0 mW 25 mW Fabry-Perot HI1060
MCLS1-1310
1310 nm 1290 - 1330 nm 2.5 mW 3 mW Fabry-Perot SMF-28e+
MCLS1-1310-15
1310 nm 1290 - 1330 nm 13.0 mW 15.0 mW Fabry-Perot SMF-28e+