manualshive.com logo in svg

THORLABS LPS710/M, Руководство пользователя


Поделиться
Скачать
background image

19

LPS710E Long Travel Piezo Stage and Controller

3.7.3 Powering Down The Controller

3.7.4 Rear Panel Connections

Fig. 3.5   Rear panel connections

STAGE connector - 

Provides the drive signal to the piezo actuator, -25 V to 150 V,

0 to 150 mA.

Warning

The controller may cause drive voltage spikes on power down. In applications 

requiring the highest sensitivity, the piezo drive voltage should be set to zero 

before the unit is powered down. 

When power is applied, do not disconnect the piezo stage from the unit.

Note

Ensure that the mating faces of the connectors on the stage and the rear 

panel of the unit are properly aligned. Misalignment can cause connection 

problems.

Tighten the securing screws to ensure that the connectors to not  become 

disconnected during use. 

150V

Содержание LPS710/M







































































Отзывы:

Нет отзывов

Похожие инструкции для LPS710/M

Samson 3510 Mounting And Operating Instructions preview
3510
Бренд: Samson Страницы: 48
Mako Networks 6000 Series Quick Installation Manual preview
6000 Series
Бренд: Mako Networks Страницы: 15
Lattice Semiconductor CrossLink Programming And Configuration Manual preview
CrossLink
Бренд: Lattice Semiconductor Страницы: 30
WAFER DC200 Manual preview
DC200
Бренд: WAFER Страницы: 15
Ebyte E180-Z5812SP Product Manual preview
E180-Z5812SP
Бренд: Ebyte Страницы: 35
IAI Msep First Step Manual preview
Msep
Бренд: IAI Страницы: 5
Rain Bird STP-400i Installation, Programming & Operation Manual preview
STP-400i
Бренд: Rain Bird Страницы: 20
Vizio Xrt302 Manual preview
Xrt302
Бренд: Vizio Страницы: 65
Sunnen HTA-2000 (2M) Manual preview
HTA-2000 (2M)
Бренд: Sunnen Страницы: 24
OJ Electronics OJ-Air2-WP55 Instructions Manual preview
OJ-Air2-WP55
Бренд: OJ Electronics Страницы: 8
Audioaccess PX-700 Manual preview
PX-700
Бренд: Audioaccess Страницы: 2
Phytec phyCORE-MCF548x Hardware Manual preview
phyCORE-MCF548x
Бренд: Phytec Страницы: 104
Xylem LOWARA Aquavara IPC Quick Start Manual preview
LOWARA Aquavara IPC
Бренд: Xylem Страницы: 292
Ashly WR-2e Installation preview
WR-2e
Бренд: Ashly Страницы: 1
OneFex CS-IO204 Manual preview
CS-IO204
Бренд: OneFex Страницы: 24
Lampert PIP 100 Operating Instructions Manual preview
PIP 100
Бренд: Lampert Страницы: 15
LAB-EL LB-762 Installation Manual preview
LB-762
Бренд: LAB-EL Страницы: 25
Cardigo 62323 Instruction Manual preview
62323
Бренд: Cardigo Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды