manualshive.com logo in svg

THORLABS Kinesis PFM450E, Руководство пользователя

Поделиться
Скачать
THORLABS Kinesis PFM450E Скачать руководство пользователя страница 24

Page 21

ETN018233-D03

PFM450E Piezo Focus Mount and Controller

4) Notice how the total travel for the associated piezo is displayed in the ‘Travel’

window - see Fig. 4.1.

Fig. 4.1   Piezo Controller Software GUI .

Caution

The PFM450 Focus Mount contains a capacitive feedback sensor and can be

driven only by the Thorlabs PPC001 150V Piezo Controller.
The controller and objective mount are calibrated at the factory and are sold as

a matched pair. The matched pair can be identified by the serial number label

that appears on both units.
Unsatisfactory performance is likely to result if the objective mount is driven by

a different controller, or if the controller is used to drive other objective mounts.

Warning: Risk of Electrical Shock

The piezo actuators in this product use high voltages. Voltages up to 150V may

be present at the STAGE connector on the rear panel.  This is hazardous and

can cause serious injury.  Appropriate care should be taken when using this

device.
Persons using the device must understand the hazards associated with using

high voltages and the steps necessary to avoid risk of electrical shock. 
The piezo controller must be switched OFF before the focus mount is plugged

in or unplugged. Failure to switch the controller off may result in damage to

either the controller, the focus mount or both.

Содержание Kinesis PFM450E




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды