background image

Electronic Variable Optical Attenuators

 

Chapter 6: Specifications 

Page 12 

 

TTN116996-D02 

Chapter 6  Specifications 

6.1. General 

Specifications 

Item #

 

EVOA800F 

EVOA800A 

Fiber Interfaces

 

2.0 mm Narrow Key 

FC/PC 

2.0 mm Narrow Key 

FC/APC 

Wavelength Range

 

780 - 980 nm  

Input Power 

200 mW (Max) 

Absolute Maximum: 250 mW 

Attenuation 
(

not including fiber coupling loss) 

Minimum: 1 dB (Typ.) 

Maximum: >25 dB 

Return Loss 

40 dB 

Digital Display Resolution 

4.5 Digits, Auto-Ranging 

Digital Display Accuracy 

5% (Typ.); 10% (Max) 

Internal Fiber 

780HP 

Fiber Coupling Loss 

1.0 - 1.5 dB (Typ.) at each Connector  

Modulation Input 

Input Voltage 

0 V to 4.9 V 

Absolute Maximum: 5.0 V 

Input Impedance 

High Z 

Bandwidth 

DC to 1 kHz (Typ.) 

Connector 

Female SMA 

Monitor Output 
Conversion Gain 

20 mV/mW 

Output Impedance 

High Z 

Bandwidth 

DC to 1 kHz (Min) 

DC to 2 kHz (Typ.) 

Connector 

Female SMA 

Battery Specifications 
Battery Life 

300 h (Typ.) from Full Charge 

Battery Charge 

3000 mAh 

Battery Charging Time 

5 h (Typ.) from 2.1 mm Coaxial Barrel Jack 

Battery Charging Input Power 

5 VDC; Up to 1 A 

Battery Charging Connectors  

2.1 mm Coaxial Barrel Jack (1 A) 

Female USB Mini-B Connector (Up to 500 mA) 

Physical Specifications 

Dimensions 

166.9 mm x 93.2 mm x 55.2 mm 

(6.57" x 3.67" x 2.17") 

Operating Temperature 

10 to 40 °C 

Storage Temperature 

0 to 50 °C 

Relative Humidity 

5% to 85% RH (Non-Condensing) 

 

Содержание EVOA800A



















Отзывы: