THORLABS DET100A2 Скачать руководство пользователя страница 7

Si Biased Detector

 

Chapter 4: Operation 

Rev A December 27, 2017 

Page 5 

Photoconductive 

In photoconductive mode, an external reverse bias is applied, which is the basis 
for our DET series detectors. The current measured through the circuit indicates 
illumination of the device; the measured output current is linearly proportional to 
the input optical power. Applying a reverse bias increases the width of the 
depletion junction producing an increased responsivity with a decrease in 
junction capacitance and produces a very linear response. Operating under 
these conditions does tend to produce a larger dark current but this can be 
limited based upon the photodiode material. 

Note 

The DET detectors are reverse biased and cannot be operated under 

forward bias conditions. 

Photovoltaic 

In photovoltaic mode the photodiode is zero biased. The flow of current out of the 
device is restricted and a voltage builds up. This mode of operation exploits the 
photovoltaic effect which is the basis for solar cells. 

4.4. Dark 

Current 

Dark current is leakage current which flows when a bias voltage is applied to a 
photodiode. Photoconductive mode tends to generate a dark current that varies 
directly with temperature. It can be inferred that dark current can approximately 
double for every 10 °C increase in temperature, and shunt resistance can 
decrease to approximately half for every 6 °C rise. Of course, applying a higher 
bias will decrease the junction capacitance but will increase the amount of dark 
current present.  

The dark current present is also affected by the photodiode material and the size 
of the active area. Silicon devices generally produce low dark current compared 
to germanium devices which have high dark currents. The table below lists 
several photodiode materials and their relative dark currents, speeds, sensitivity, 
and costs. Please note that sensitivity values in the table are typical values; 
Thorlabs offers photodetectors with sensitivity ranges that vary from those shown 
below. 

 

 

Содержание DET100A2





















Отзывы: