THORLABS BBD101 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 76

background image

15

Single-Channel Brushless DC Servo Controller

3.3.3

Rear Panel Connections

Fig. 3.1 Rear panel connections

CH ID

- For channel selection when using the MJC001 joystick - see Section 4.9.

MOTOR DRIVE

-

Provides all phase current drive connections to the DC motor

actuators - see Section A.1.

FEEDBACK

-

Provides connection for the position encoder feedback signals - see

USER I/O

- The ‘USER I/O’ connector exposes a number of electrical signals useful

for external control and monitoring - see Section A.3. for more details.

USB

- USB port for system communications.

HANDSET IN -

Provides connection for the Thorlabs Joystick, MJC001.

INTERCONNECT -

Allows several controllers to be ‘Daisychained’. The

INTERCONNECT terminal should be connected to the HANDSET IN connector on
the next unit in the chain.

TRIG IN

– For Future Use.

TRIG OUT

– For Future Use.

AUX I/O

- The AUX I/O connector exposes a number of internal electrical signals. For

convenience, a number of logic inputs and outputs are included, thereby negating the
need for extra PC based IO hardware. Using the APT support software, these user
programmable logic lines can be deployed in applications requiring control of external
devices such a relays, light sources and other auxillairy equipment. - see Section A.4.
for further details.

Note

The USB cable length should be no more than 3 metres unless a powered

USB hub is being used.

«
...
13
14
15
16
17
...
»

Содержание BBD101













































































Отзывы:

Нет отзывов

Похожие инструкции для BBD101

Бренд: Rain Bird Страницы: 48

Бренд: Galcon Страницы: 32

Бренд: Magnescale Страницы: 132

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: Campbell Страницы: 3

Бренд: ZKTeco Страницы: 2

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Barcelona Страницы: 8

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

Бренд: Paradox Страницы: 2

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Nemesis Страницы: 6

Бренд: Dantel Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды