background image

TD 190_E 

Mounting or exchanging a pick-up cartridge 

Instead of the factory-supplied pick-up cartridge any  
other cartridge with standard half-inch mounting 
holes and a weight between 3 and 10 grams can be 
installed. To do this loosen the collar-lock (

9

) and 

pull off the head shell (Fig. 7). Unscrew the cartridge 
and carefully remove the coloured signal leads from 
the cartridge pins with a pair of tweezers. Screw the 
new cartridge onto the head shell but do not tighten. 
Attach the leads to the pins while observing the 
correct coding. 

 

Fig. 7 

 
Please note: The example shown in Fig. 8 is appli- 
cable only for the pick-up cartridge OMB 10! 

 
For the precise adjustment of the so-called stylus 
overhang push the head shell with cartridge into the 
supplied mounting gauge. The adjustment is correct 
if the stylus is flush with the V-shaped recess in the 
gauge as viewed from above. When viewed from the 
side the stylus should be seen within the rectangular 
recess of the gauge (Fig. 9). Adjust the cartridge in 
the head shell until the correct positions are 
achieved. Lastly, tighten the mounting screws, put 
the head shell with cartridge back on the tone arm 
and tighten the collar-lock (9). 

ATTENTION! 

During these mounting and adjustment procedures 

Fig. 8

 

you must be very careful not to damage the delicate 
stylus and cantilever by uncontrolled and brisk 
movements. 

 

Replacing the stylus 

Any stylus is subject to wear even under normal 
playing conditions. Therefore, it is highly 
recommended to have the cartridge, respectively its 
stylus, inspected after about 500 hours of playing. 
This is because a worn or damaged stylus will 
eventually damage your precious vinyl records! 
In order to playback vintage shellac records (78's) 
with optimal results the original stylus should be 
exchanged with a suitable special stylus for shellacs. 
Please consult your THORENS dealer for further 
information and details. 
 
 
 
 
 
 
 
 
 
 
 
 

Fig. 9

 

 

 

 

red 

right channel 

RG  = 

green 

right channel ground 

white 

left channel 

LG  = 

blue 

left channel ground

 

Содержание TD 190










Отзывы: