6
6
Daily use
How to switch on the set?
With the On/Off-button fitted on the set. When the red
LED is lit, the TV set has previously been switched on
standby with the key
B
B
on the remote control.
If the red LED flashes, it means that the control
keyboard of the TV is locked and can only be made
operational again through the remote control.
In both cases, enter a channel number.
How to select a channel?
Through the digital keys of the remote control.
For the 2-digit channels (10, 11, 12, etc.) press on
key 0 of the remote control.
Ò --Ó appears on the screen. Through the digital
keys, enter the tens unit digit, then the unit one.
With the pr+ or pr- button of the remote control or
the keypad.
If you change the channel with the pr+ or pr- buttons
of the keypad, maintain the button pressed until the
next or preceding channel appears on the screen.
How to select the Sound channel?
This function may only be accessed if you selected
Auto on the
line of the Sound menu (see p. 6).
Press the blue key to successively select S1, S2 or S3
during NICAM, Stereo or Dual telecasts, or when
using a device connected to one of the AV
connections.
How to adjust the volume?
- With the remote control, by making short pulses or
maintaining the
/
buttons pressed.
- With the keypad of the television, by maintaining
buttons
/
pressed.
How to mute the sound?
With the (
) key.
Press once more on the key to reactivate the sound.
How to display the channel number?
With the info key, display or remove the channel
number and, if you want it, the time left before timer-
programmed switch-off.
How to recall the preferred settings?
Press on the red key to recall the sound and picture
settings you previously stored (see page 6).
How to programme a switch-off?
Press on the Green
key, then using the Left/Right
keys, adjust on the screen the wished-for duration
before the switching-off of the TV set (by intervals of
10 minutes up to 4 hours).
To exit the menu, press exit.
When the programmed remaining time is over, the
TV set will switch on standby
60 seconds before automatic cut-off, a message
appears on the screen.
To cancel, first press the Green key
and then, by
means of the directional key Left, reset the time
remaining on -:--.
The programmed switching-off is also deactivated when
the TV set is turned off through its own On/Off switch.
How to prevent kids using the TV set?
Hold key
B
B
on the remote control down for over 4
seconds until the red LED on the TV set flashes.
The keys of the TV set are now locked and switching
it on again will be possible by means of the remote
control only.
Keep the remote control out of the reach of children.
To unlock the keys of the TV set, make use of the
number keys on the remote control.
The keys of the TV set will also remain locked after
timer-programmed switching-off.
The lock function will also be activated when the TV
set is switched on standby or switched off with its
On/Off switch before the time remaining until
programmed switching-off is over.
How to switch off the set?
To switch the TV set off, press the key
B
B
on the
remote control or use the On/Off switch on the TV set.
The TV set automatically switches to stand-by after a
few minutes without telecast on the selected channel.
Important:
The blue screen displaying SIGNAL = 0 either means
that the television set is not receiving any signal, or
that the channel on which you are tuned is receiving
two signals at the same time, which is preventing the
synchronisation of the television set. Change
programs and if the display persists, check your
antenna connection.
Sound received
S1
S2
S3
NICAM Stereo
Stereo
Mono
X
NICAM Dual
NICAM 1 NICAM 2 Mono
NICAM Mono
NICAM
Mono
X
Stereo
Stereo
X
X
Dual
Dual 1
Dual 2
Mono
Mono
X
X
FM Mono
X
X
X
AVsound
Stereo
Channel L Channel R
X: Not available
tx807en2 15/01/03 12:26 Page 6
