Thomashilfen tGo, Инструкция по эксплуатации

Страница: 21 / 28

2021-04
Setup and assembly
At delivery, the tGo is knocked down into its individual parts. Follow these individual steps to assemble your tGo:
1.
Place the wide central tube into the locator on the subframe such that the holes in the tube are aligned with the
holes in the locator (Fig. 4). Fit the Allen bolts provided through the holes in the frame locator and central tube from
the inside (Fig. 5).
2. Take the plastic eye with pre-fitted nuts and offer this up to the holes in the front side of the tGo through which the
Allen bolts are protruding. Tighten the screws into the nuts in the plastic eye. Ensure that the central tube and sub-
frame are securely fastened together (Fig. 6).
3.
Tighten the two Allen bolts in the black plastic part inside the lower end of the central tube. Ensure that each bolt is
turned fifteen times at least (Fig. 7).
4.
Now loosen the Allen bolt that is screwed into the front element of the central articulating arm from the side. Press
the articulating arm onto the central tube such that the arm is pointing towards the inside of the tGo frame and the
bulged part of the front metal element is facing upwards. Align the articulating arm at right angles to the front side of
the subframe and fasten with the Allen bolt that is located on the front element (Fig. 8). Ensure that the central tube
and articulating arm are securely fastened together and that the articulating arm cannot slip downwards under load.
5. Loosen the lower nut that is located on the threaded rod beneath the saddle. Insert the threaded rod into the fore-
most of the two locating holes in the rearmost element of the articulating arm (Fig. 9). In front of the saddle is a tube
that points upwards. Ensure that the saddle – together with the tube – is inserted into the locator in the direction of
travel. Replace the removed nut onto the threaded rod beneath the articulating arm. In so doing, ensure that the rub-
ber O-ring within the nut is facing upwards (Fig. 10). Tighten the nut.
6.
Take the handlebars in your hands. Undo the Allen bolt in the joint at the upper end of the handlebar tube. To do
this, the locking lever must first be released and the handlebar positioned such that the hole in the handlebar locator
aligns with the oblong hole in the handlebar tube (Fig. 11). Now the long end of the Allen wrench can be inserted
into the tube until it locates into the head of the Allen bolt (Fig. 12). Undo the bolt.
7. Insert the handlebar tube into the central tube of the tGo (Fig. 13). You can turn the handlebar through 360° within
the central tube. This allows you to choose whether the handlebar locating bracket should face forwards (Fig. 14) or
backwards (Fig. 15). Then align the handlebar so that it is parallel with the front side of the tGo. Secure the handle-
bar by fully tightening the Allen bolt inside the handlebar tube. Place the handlebar in the desired position and lock
in-place with the locking lever (Fig. 16). Secure the locking lever with the built-in slider.
8.
Slot the pelvis pad onto the tube in front of the saddle. To do this, the screw on the tube locator must first be loos-
ened. The Allen bolts that connect the various pads should be fitted such that their heads are pointing upwards.
Tighten the screw on the tube locator in order to secure the pads in position (Fig. 17).
9.
To fit the chest pads, first loosen the screw in the chest pad tube. Slot the tube into the tGo saddle tube such that the
chest pads are positioned above the pelvis pads (Fig. 18). Secure the tube in-place by tightening the internal screw.
10. To fit the torso pads, first loosen the locking lever on the back of the torso rest. From behind, push the torso rest tube
into the tube on which the saddle is mounted. Secure the torso rest with the locking lever (Fig. 19).
Teaching the User
The user is taught how to use this device by trained staff who will reference these Instructions for Use.
Instructions for Use – t Go
21