1
.
MIC2
INPUT
PORT
Unbalanced
6
.
3mm
TS microphone connector.
2
.
MIC3
INPUT
PORT
Unbalanced
6
.
3mm
TS microphone connector.
3
.
AUX1 INPUT PORT
Stereo RCA unbalanced input port for AUX1.
4
.
AUX2 INPUT PORT
Stereo RCA unbalanced input port for AUX1.
5
.
AUX OUTPUT PORT
Stereo RCA unbalanced output port for external
amplifier or recording device.
6
.
MUTE CONTROL KNOB FOR MIC1 PAGING
7
.
FM ANTENNA TERMINALS
The FM terminal accepts a 75 Ohm Coaxial cable that
terminates at an FM antenna. Antenna position may
affect performance so it may be necessary to
reposition the antenna for the best reception.
Note: The ability to receive an FM signal may be
diminished by terrain, area buildings, and the
construction materials of the building housing the
receiver. Keep these circumstances in mind when
selecting the type of FM antenna and its mounting
position.
An indoor FM antenna is provided and should be
suitable for most applications. Repositioning the
antenna may be necessary to identify the optimum
mounting location. If greater signal strength is required,
replace the supplied antenna with a large outdoor FM
antenna using 75 Ohm coax as the lead wire.
8
.
8
Ω
SPEAKER
OUTPUT
TERMINAL
Connect “8
Ω"
to the
"+"
of
8ohms speaker
.
9
.
8
Ω
SPEAKER
OUTPUT
TERMINAL
Connect “GND” to the
"-"
of
8ohms speaker
.
Rear Panel
www.thinuna.com Page 5 Version A
10
.
ZONE(1) 100V SPEAKER OUTPUT TERMINAL
Connect
to the
"+"
of
zone(1)
100V
speaker.
11
.
ZONE(2) 100V SPEAKER OUTPUT TERMINAL
Connect
to the
"+"
of
zone(2)
100V
speaker.
12
. "
COM
"
TERMINAL FOR ZONE1~6 OUTPUT
Connect to the
"-"
of
zone1
~
6
100V
speaker.
13
.
ZONE(3) 100V SPEAKER OUTPUT TERMINAL
Connect
to the
"+"
of
zone(3)
100V
speaker.
14
.
ZONE(4) 100V SPEAKER OUTPUT TERMINAL
Connect
to the
"+"
of
zone(4)
100V
speaker.
15
.
ZONE(5) 100V SPEAKER OUTPUT TERMINAL
Connect
to the
"+"
of
zone(5)
100V
speaker.
16
.
ZONE(6) 100V SPEAKER OUTPUT TERMINAL
Connect
to the
"+"
of
zone(6)
100V
speaker.
Note
:
the
power
capacity
for
each zone can reach
the rated power of amplifier. But make sure that the
total power of zone 1~5 can not exceed the rated power.
17
.
AC POWER CORD
Connect only to an proper AC mains power source.
18
.
AC FUSE HOLDER
The fuse holder contains the AC overload
protection fuse. If the fuse has blown out, replace
it with a fuse of the same specifications. If the fuse
continues to blow, refer servicing to a qualified
service technician.
19. FAN VENTS
These vents provide hot air flow out of the unit.
It is important to keep them free of obstructions,
to prevent the unit from overheating. It is also
important to operate the unit in a dust-free
environment.
1 2 3 4 5 6 7 8 10 12 14 15 12 17 18 19
9 11 13 12 16
VTA-240
F
/360F/480F/600F II 6 Zones MP3
/
Tuner
/
BT
Mixer Amplifier
