Thinklogical VX640 Скачать руководство пользователя страница 25

 

VX640 Router Manual, Rev. D 

20 

August, 2013 

 

 

Step 3 
Once the module is completely seated, hand-tighten the thumbscrews.  

Warning!

  Do not tighten the thumbscrews with a screwdriver.

  

How to Install or Replace an Interconnect Module 

Note: Replacing the Interconnect Module will interrupt service. 

To  replace  the  Interconnect  Module,  the  front  door  and  front  panel  must  first  be  removed.    (See 
Appendix C, page 31.) 

 

Step 1  
Turn both front door latches one quarter turn clockwise (arrow on knob pointing up) to release the door. 

 

Step 2  
While holding the door steady with one hand, pull down the upper spring-loaded hinge release and pull 
the  upper  portion  of  the  door  outward  until  the  latch  clears  the  mounting  hole.  The  door  can  now  be 
removed and set aside. 

Warning!   

KEEP  THE  DOOR  CLOSED  WHEN  IN  USE!    The  VX640  Front  Door  contains  air-

flow baffles that are integral to the router’s cooling system.  Do not leave the front door off 
the  chassis  for  an  extended  length  of  time  if  the  unit  is  running.    Keeping  the  front  door 
open for an extended period of time will lead to a malfunction of the VX640. 

 

Step 3  
There are two thumb screws holding the front panel to the chassis.  Loosen the thumb screws, remove 
the front panel and set it aside.   

 

Step 4  
There  are  two  thumbscrews  on  the  Interconnect  Module;  turn  the  thumbscrews  counterclockwise  until 
they disengage from the chassis.  Pull the Interconnect Module out using both black ejector handles. 

 

Step 5 
Place the new module upright so that the four Status LEDs are at the bottom. Grasp the module 
by  the  handles.  The  card  should  slide  in  freely  until  it  reaches  the  backplane  connector.    At this 
point, use just enough force to firmly engage the card with the mating connector. 

Warning!

  If the module does not slide easily into the connector, do not force it!  Damage 

may occur.  Remove the card and start over.  

Step 6 
Once the module is completely seated, hand-tighten the thumbscrews.  

Warning!

  Do not tighten the thumbscrews with a screwdriver.

  

Step 7 
Replace the front panel that was removed in Step 3

 

Step 8 
Replace the front door that was removed in Steps 1 and 2

Содержание VX640













































Отзывы: