ThingMagic Astra-EX Скачать руководство пользователя

Страница: 16 / 94

Setting Up the Reader

M6 and Astra-EX User Guide

Setup Procedure

The steps required to set up and run the M6 and Astra-EX Reader are:

Connecting Antenna(s) to the Reader

Powering Up the Reader

Connecting Your PC to the Reader

Communicating with the Reader using a Link-local Address

Logging On to the Reader

Connecting Antenna(s) to the Reader

The M6 Reader supports up to four monostatic antennas. The default power setting that

you configure is applicable to all antennas, although per-antenna settings are supported.
See

Settings Page

for configuration options.

Before you apply power to the Reader, you must connect at least one antenna to an RFID

antenna port. When the Reader is powered on, any port that is not connected and
meeting the

Antenna Detection

requirements is disabled.

Note

Use only authorized antennas and cables. See

Appendix A: M6 and Astra-EX

Antenna and Cable Information

Содержание Astra-EX































































































Результаты поиска

Содержание Astra-EX

Отзывы:

Похожие инструкции для Astra-EX

Бренды по названию

Популярные бренды

ThingMagic Astra-EX, Руководство пользователя

Результаты поиска

Содержание Astra-EX

Отзывы:

Похожие инструкции для Astra-EX

Бренды по названию

Популярные бренды