manualshive.com logo in svg

THIEMAN Series TVLR 125A, Руководство пользователя

Поделиться
Скачать
THIEMAN Series TVLR 125A Скачать руководство пользователя страница 5

5.

8.   DO NOT OVERLOAD THE LIFTGATE. Each liftgate has a specific maximum capacity for 

lifting and lowering. The standard maximum rated capacity of the TVLR series liftgates 

differs with each model as follows: 

                                            TVLR125-1250 lbs. Maximum Load

                                            TVLR16-1600 lbs. Maximum Load

  

WARNING note:  Special options can lower the maximum rated capacities below 

those shown above. Be certain you know what the maximum rated capacity is for your 

particular liftgate.

9.   NEVER off-center the load on the platform, from side to side or away from truck as this 

may overload the liftgate. The center of weight of the load should NEVER be placed 

beyond the center of the platform load surface, away from truck. Loads should be placed 

close to platform edge nearest truck. See figure 1.

10.   NEVER allow any part of the load to extend beyond the edges of the platform’s flat load 

surface. Overhanging objects increase the risks of tipping loads due to unstable loading 

or snagging these objects on surroundings and THESE OBJECTS COULD ALSO STRIKE 

OR CRUSH OPERATORS OR BYSTANDERS.

11.   NEVER step on or place loads on, the ramp portion of any liftgate platform (includes 

all ramp styles), unless the platform is lowered completely to the ground and the entire 

platform and ramp are supported by the ground.

12.  NEVER lift or lower unstable loads.

13.  NEVER operate liftgate if platform load surface is slippery.

            

14.   Make certain the areas above and below the liftgate platform and other moving liftgate 

parts, are clear before, and at all times during, operation of the liftgate.  Do NOT allow 

anyone to stand around the platform where a falling load could land on them.

15.  Load and unload the platform from the rear and not from the side of the platform.            

Never remove the platform support chains to load or unload the platform.

16.  Never operate lift trucks on or over any part of the platform.

17.   Follow  all  sections  in  this  manual  with  “Maintenance”  in  the  title  –  refer  to  “Table  of                    

Contents” on Page 2.  

18.   NEVER move vehicle unless platform is properly stowed and power is off. An open liftgate 

on a moving vehicle poses a serious traffic hazard.

(Warnings continued on following pages)

Содержание Series TVLR 125A





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды