6
So, to do it, the input and static bypass switches will have to
be turned «Off».
Put warnings of danger and/or emergency switches if the safety
Standards require it in your particular installation.
Ŗ
It is possible that the UPS supplies output voltage
through the manual bypass to those equipments that
incorporate it either standard or optional, so it will have to be
considered as regards to safety. If it were necessary to break
the output supply of the equipment in this situation, deactivate
the outgoing distribution protection or in case of lack of it the
general protection of the distribution panel that feeds the UPS.
Ŗ
All power supply electrical cables have to be fixed to the
equipments and loads, interfaces, etc..., to unmovable parts
and in the way to avoid treads, trips on them or fortuitous
pulls.
Ŗ
CHASSIS or RACK mounted equipments are destined to be in-
stalled in a predetermined set to be done by professionals.
The installation has to be designed and executed by qual-
ified personnel, who will be the responsible to apply the
safety and EMC regulations and standards that controls
the particular installations where the product is destined.
The equipments assembled in CHASSIS do not have
enclosure protection, even the power blocks are unpro-
tected.
Some RACK mounted equipments do not have the power
blocks protected.
Ŗ
Never manipulate the equipment with wet hands.
1.2.3.2. To keep in mind.
Ŗ
Do not try to dismantle or change any part of the
equipment, if this action is not contemplated in this
document. Manipulation inside the UPS due to any modifica-
tion, reparation or any other cause, can make an electrical
discharge of high voltage and it is restricted to qualified staff
only. Do not open the equipment.
A part from the implicit stated risks, any action that make the
modification, internal or external of the equipment or just only
the simple intervention inside of itself, which is not stated in
this document, it can expire the warranty.
Ŗ
If it is observed that the UPS exhausts smoke or toxic gas,
shutdown it immediately and disconnect it from the power
supply. This kind of fault can cause fire or electrical dis-
charge. Contact with our
(
S.T.S.
)
.
Ŗ
In case of an accidental equipment dropping or if the enclo-
sure is damaged, do not start it up under any concept. This
kind of fault can cause fire or electrical discharge. Contact
with our
(
S.T.S.
)
.
Ŗ
Do not cut, manipulate the electrical cables, do not put heavy
objects over them too. Any of these actions could cause a
short-circuit and make a fire or electrical discharge.
Check that the electrical cables of connection, plugs and out-
lets are in good conditions.
Ŗ
When moving an equipment from a cold place to a warm en-
vironment and vice versa, it can cause condensation (small
water drops) in the external and internal surfaces. Before in-
stalling a moved equipment from another place or even pack-
aged, the equipment will be left for a minimum time of two
hours in the new location before making any action, with the
purpose of adapting it to the new environmental conditions
and avoid the possible condensations.
The UPS has to be completely dry before starting any instal-
lation task.
Ŗ
Do not store, install or expose the equipment in corrosive,
wets, dusty inflammable or explosive environments and
never outdoors.
Ŗ
Avoid to locate, install or store the equipment in a place with
direct sunlight or high temperatures. Batteries could be dam-
aged.
In the exceptional case and long exposition to intense heat,
batteries can cause filtrations, overheating or explosions,
which can cause fires, burn or other injuries. High tempera-
tures can also make deformation in the plastic enclosure.
Ŗ
The location will be spacious, airy, away from heat sources
and easy access.
Ŗ
Do not obstruct the cooling grids by entering objects through
themselves or other orifices.
Ŗ
Leave as minimum space of 25 cm in the equipment pe-
ripheral.
Ŗ
Do not put materials over the equipment or parts that obstruct
the correct visualization of the synoptic.
Ŗ
Be careful to not wet it, because it is not waterproof. Do not
allow entering any kind of liquids in. If accidentally the outside
of the machine comes into contact with liquids or salt air, dry
it with a soft and absorbent cloth.
Ŗ
To clean the equipment, wipe over a damp cloth and then
dry it. Avoid sprinkling or spillage that could enter through the
slots or cooling grids, which may cause fire or electric shock.
Do not clean the equipments with products that could have
alcohol, benzene, solvent or other inflammable substances,
or they are abrasive, corrosive, liquids or detergent.
Ŗ
Be careful to not lift heavy loads without help, according to
the following recommendations:
d
, < 18 kg.
dd
, 18 - 32 kg.
ddd
, 32 - 55 kg.
, > 55 kg.
Ŗ
UPSs are electronic equipments, so they will be treated as
they are:
Avoid shocks.
Avoid jolting or bouncing of the UPS, like those produced
by moving the equipment on a hand truck and move on
an uneven or wavy surface.
Ŗ
UPS transport will be done packaged inside its original pack-
aging in order to prevent it from shock and impact and by
means of the suitable type of packaging (carton box, pallet
packaging, ...) and appropriate to its weight.
Ŗ
Although the physical location of the elements can differ from
the illustrations in this manual in some cases, the correct la-
belling correct the possible doubts and makes easy its com-
prehension.
1.2.3.3. Safety warning regarding batteries.
Ŗ
The manipulation and connection of the batteries
shall be done and supervised by personnel with
battery knowledge only.
Before doing any action, disconnect the batteries. Check that
no current is present and there is not dangerous voltage in
the DC BUS (capacitors) or in the endpoint of the battery set
terminals.
Battery circuit is not isolated from input voltage. Dangerous
voltages can be found between the terminals of the battery
set and the earth. Check that there is not any voltage at the
input before take any action over them.
USER MANUAL
Thiele KG • V
orderer W
einberg 26 • D-71522 Backnang • T
el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni
c.de • www
.thiele-electronic.de
Thiele KG • V
orderer W
einberg 26 • D-71522 Backnang • T
el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni
c.de • www
.thiele-electronic.de
Vorderer Weinberg 26
• D-71522 Backnang •
Tel.:+49 (0)7191 3560-0 (Fax.:-19)
