background image

CAUTION

If ignition does NOT occur in 5 seconds, turn the 

burner controls OFF, wait 5 minutes and repeat the 

lighting procedure. If the burner does not ignite with 

the valve open, gas will continue to flow out of the 

burner and could accidently ignite with risk of injury.

Match-Lighting

s

 Do not lean over grill while lighting.

1. Open lid during lighting.  
2.

3.

4.

To ignite right burner, turn knob to PRE-HEAT.

Place lit match into match holder, then into side of grill bottom 
(as shown below). 

Push in and turn left  knob to      PRE-HEAT. Be sure burner 
lights and stays lit.

8  •  461630208

Ignitor Lighting

s

 

 Do not lean over grill while lighting.

Burner Flame Check

• Remove cooking grates and flame tamers. Light burners, rotate 

knobs from HI to LO. You should see a smaller flame in

 

LO 

position than seen on HI. Always check flame prior to each use. 
If only low flame is seen refer to "Sudden drop or low flame" in 
the 

Troubleshooting Section

.

HI

LO

Turning Grill Off

• Turn all knobs to  

position. Turn LP cylinder off by turning 

hand-wheel clockwise to a full stop.

Ignitor Check

• Turn gas off at LP cylinder.

 Press ignitor button rapidly.  

"Click" should be heard and spark seen each time between 
collector box or burner and electrode. See 

"Troubleshooting"

 if 

no click or spark.

Valve Check

• Important: Make sure gas is off at LP cylinder before 

checking valves

.  Knobs lock in  

position. To check 

valves, first push in knobs and release, knobs should spring 
back. If knobs do not spring back, replace valve assembly 
before using grill. Turn knobs to

 LO

 position then turn back to  

position. Valves should turn smoothly.  

Hose Check

Before each use, check to see if hoses are cut or worn. 
Replace damaged hoses before using grill. Use only 
valve/hose/regulator specified by manufacturer.

General Grill Cleaning 

• Do not mistake brown or black accumulation of grease and 

smoke for paint.  Interiors of gas grills are not painted at the 
factory 

(and should never be painted)

. Apply a strong solution 

of detergent and water or use a grill cleaner with scrub brush 
on insides of grill lid and bottom. Rinse and allow to completely 
air dry. 

Do not apply a caustic grill/oven cleaner to painted 

surfaces.

 

• 

Plastic parts: 

Wash with warm soapy water and wipe dry.

s

 

Do not use citrisol, abrasive cleaners, degreasers or a 

concentrated grill cleaner on plastic parts. Damage to and 
failure of parts can result. 

• Porcelain surfaces: 

Because of glass-like composition, most 

residue can be wiped away with baking soda/water solution or 
specially formulated cleaner.

 

Use nonabrasive scouring powder 

for stubborn stains.

• Painted surfaces: 

Wash with mild detergent or nonabrasive 

cleaner and warm soapy water. Wipe dry with a soft 
nonabrasive cloth.

OFF 

OFF 

 

OFF 

 

•Cooking surfaces: 

 If a bristle brush is used to clean any of 

the grill cooking surfaces, ensure no loose bristles remain on 
cooking surfaces prior to grilling. It is not recommended to 
clean cooking surfaces while grill is hot.

Содержание 461630208





























Отзывы: