ThermoForma Cryomed 1010 страница 24 Скачать руководство пользователя

Страница: 24 / 29

5.3 Troubleshooting Chart - Freezing Chamber (continued)

Problem Probable

Cause

Remedy

Fan is not operating.

Faulty limit switch.

Replace switch.

Fan has not been energized at the controller.

Energize fan at controller.

Fan is jammed or motor is defective.

Mechanically free fan and/or replace fan motor.

Inability to sufficiently

LN2 transfer hose connected to vent side of supply tank.

Connect transfer hose to liquid side of

cool specimens.

supply tank.

Controller is improperly set.

Readjust controller setting (add Cool+).

Insufficient liquid nitrogen pressure at freezing chamber.

Increase liquid nitrogen supply pressure

to 22 PSIG as measured at the freezing chamber.

Defective limit switch.

Replace limit switch.

Nitrogen gas is escaping

Liquid nitrogen pressure supply is too high.

Reduce liquid nitrogen pressure to 22 PSIG.

from pressure relief valve

Pressure relief valve is defective.

Replace pressure relief valve.

at rear of freezing chamber.

Heater in freezing chamber

Heater has not been energized at controller.

Energize heater.

does not operate.

Element is faulty.

Replace faulty heating element.

Heater relay is faulty.

Replace faulty heater relay.

Wiring connections are faulty.

Check wiring harness for proper

connector seating at controller.

Models 1010 and 1011 ________________________________________________________________________Maintenance

5 - 3

Содержание Cryomed 1010






























Результаты поиска

Содержание Cryomed 1010

Отзывы:

Похожие инструкции для Cryomed 1010

Бренды по названию

Популярные бренды

ThermoForma Cryomed 1010, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Cryomed 1010

Отзывы:

Похожие инструкции для Cryomed 1010

Бренды по названию

Популярные бренды