manualshive.com logo in svg

thermofin TCS.2 Series, Руководство по эксплуатации, Страница: 19 / 162

Поделиться
Скачать
thermofin TCS.2 Series Скачать руководство пользователя страница 19

 

Controller operating manual

 

15.11.2020 – Version 1.1 

TCS.2 series –  

thermofin

®

 control system 2

nd

 generation

 

Page: 19/162 

 

Operating manual - translation into English © thermofin GmbH 

Picture 4 

Picture 5 

  Passwords 

For security reasons, the device settings and the editable parameters are password-protected. The 

following three access levels are distinguished: 

  

  Manufacturer password 

This password protects basic factory settings. Parameters such as device type, design, resetting 

operating hours counter, addressing fans, etc. are not accessible to the user. 

 

  Admin device password 

The password for the device settings can be 

requested from the manufacturer or supplier 

of the TCS if required. 

 

  User parameter password (editable) 

The factory-set password for parameter changes (setpoints, control parameters, time/date, etc.) is 

“

3333

”. The operator can change this to his/her own password that is known only to him/her. 

  

 

The following procedure is used to change the parameter password: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  Hold down the “DELETE PASSPORD” button for 5 seconds (Picture 5) 

 

 

Then the following window opens. If the system password has already been entered, this step is skipped (22a) 

Содержание TCS.2 Series



































































































































































Отзывы:

Нет отзывов